D-Link DES-3326SRM Command Line Interface Reference Manual Download

Page: 340 / 354

DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual

340

OSPF Configuration Commands

delete ospf virtual_link

<neighbor_id>

−

The OSPF router ID for

the remote area. This is a 32-bit number
in

the

form

address

(xxx.xxx.xxx.xxx) that uniquely identifies
the remote area

’

s Area Border Router. The

router ID of the neighbor router.

Restrictions

Only administrator-level users can issue
this command.

Usage Example

To delete an OSPF virtual interface from the switch:

DES-3326SR:4#delete ospf virtual_link 10.1.12 20.1.1.1
Command: delete ospf virtual_link 10.1.12 20.1.1.1

Success.

DES-3326SR:4#

show ospf virtual_link

Purpose

Used to display the current OSPF virtual
interface configuration.

Syntax

show ospf virtual_link {<area_id>
<neighbor_id>

Description

This command will display the current
OSPF virtual interface configuration.

Parameters

<area_id>

−

A 32-bit number in the form of

an IP address (xxx.xxx.xxx.xxx) that
uniquely identifies the OSPF area in the

Summary of Contents for DES-3326SRM



































































































































































































































































































































































Search results

Summary of Contents for DES-3326SRM

Reviews:

Related manuals for DES-3326SRM

Brands by name

Popular brands

D-Link DES-3326SRM, Command Line Interface Reference Manual

Search results

Summary of Contents for DES-3326SRM

Reviews:

Related manuals for DES-3326SRM

Brands by name

Popular brands