manualshive.com logo in svg

D-Link DES-3326SRM, Command Line Interface Reference Manual

The D-Link DES-3326SRM product comes with a comprehensive Command Line Interface Reference Manual perfect for users seeking in-depth technical assistance. This manual provides crucial information for configuration and troubleshooting. Download the user manual for free from our website and unlock the full potential of your DES-3326SRM device.

Share
Download
background image

DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual 

VLAN Commands 

175 

 

 

create vlan 

Purpose 

Used to create a VLAN on the switch. 

Syntax 

create vlan <vlan_name> {tag 
<vlanid>/advertisement} 

Description 

This command allows you to create a VLAN 
on the switch. 

Parameters 

<vlan_name> 

−

 The name of the VLAN to be 

created. 

<vlanid> 

−

 The VLAN ID of the VLAN to be 

created. 

advertisement 

−

  Specifies the VLAN as able 

to join GVRP.  If this parameter is not set, 
the VLAN cannot be configured to have 
forbidden ports. 

Restrictions 

Each VLAN name can be up to 32 
characters.  If the VLAN is not given a tag, it 
will be a port-based VLAN.  Only 
administrator-level users can issue this 
command. 

Example Usage: 

To create a VLAN v1, tag 2: 

DES-3326SR:4#create vlan v1 tag 2 
Command: create vlan v1 tag 2 
 
 Success. 
 
DES-3326SR:4# 

Summary of Contents for DES-3326SRM



































































































































































































































































































































































Reviews:

No comments

Related manuals for DES-3326SRM

D-Link xStack User Manual preview
xStack
Brand: D-Link Pages: 357
Xantech AC1 Installation Instructions preview
AC1
Brand: Xantech Pages: 2
socomec 95333400 Instruction Manual preview
95333400
Brand: socomec Pages: 43
Cabletron Systems SmartSwitch 2500 Reference Manual preview
SmartSwitch 2500
Brand: Cabletron Systems Pages: 402
S&C Omni-Rupter Series Installation And Operation Manual preview
Omni-Rupter Series
Brand: S&C Pages: 31
Lantech IES-5222T Series User Manual preview
IES-5222T Series
Brand: Lantech Pages: 30
Jabra EHS - Brochure preview
EHS -
Brand: Jabra Pages: 13
Leviton 47693-ESM Product Specifications preview
47693-ESM
Brand: Leviton Pages: 2
Alloy POEFE8TV2 User Manual preview
POEFE8TV2
Brand: Alloy Pages: 13
Banner SI-HG63FQDR Instruction Manual preview
SI-HG63FQDR
Brand: Banner Pages: 8
AVLinx ADV2.1 Instruction Manual preview
ADV2.1
Brand: AVLinx Pages: 10
3onedata IES6100 Series Quick Installation Manual preview
IES6100 Series
Brand: 3onedata Pages: 4
Tekmar tekmarNet 4 User Switch 481 Data Brochure preview
tekmarNet 4 User Switch 481
Brand: Tekmar Pages: 12
Korenix JetNet 5428G-20SFP Series Quick Installation Manual preview
JetNet 5428G-20SFP Series
Brand: Korenix Pages: 2
Club 3D SenseVision CSV-1370 Manual preview
SenseVision CSV-1370
Brand: Club 3D Pages: 4
AVProEdge AC-AEX-RC-HUB User Manual preview
AC-AEX-RC-HUB
Brand: AVProEdge Pages: 31
Rosewill RHUB-200 User Manual preview
RHUB-200
Brand: Rosewill Pages: 3
Velux ACTIVE with NETATMO Installation Instructions Manual preview
ACTIVE with NETATMO
Brand: Velux Pages: 20

Brands by name

Popular brands

Load more brands