manualshive.com logo in svg

D-Link DES-3326SRM, Command Line Interface Reference Manual

The D-Link DES-3326SRM product comes with a comprehensive Command Line Interface Reference Manual perfect for users seeking in-depth technical assistance. This manual provides crucial information for configuration and troubleshooting. Download the user manual for free from our website and unlock the full potential of your DES-3326SRM device.

Share
Download
background image

DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual 

Port Mirroring Commands 

171 

 

Example Usage: 

To delete the mirroring ports:

 

 

DES-3326SR:4#config mirror 1:5 delete source 1-5 both 
Command: config mirror 1:5 delete source 1-5 both 
Success. 
DES-3326SR:4# 

 

enable mirror 

Purpose 

Used  to  enable  a  previously  entered  port 
mirroring configuration. 

Syntax 

enable mirror 

Description 

This  command,  combined  with  the  disable 
mirror command below, allows you to enter 
a  port  mirroring  configuration  into  the 
switch, and then turn the port mirroring on 
and  off  without  having  to  modify  the  port 
mirroring configuration. 

Parameters 

none. 

Restrictions 

none. 

 

Example Usage: 

To enable mirroring configurations: 

 

DES-3326SR:4#enable mirror 
Command: enable mirror 
 Success. 
DES-3326SR:4# 

Summary of Contents for DES-3326SRM



































































































































































































































































































































































Reviews:

No comments

Related manuals for DES-3326SRM

Zektor HDA800 User Manual preview
HDA800
Brand: Zektor Pages: 65
WAGO 852-1102 Manual preview
852-1102
Brand: WAGO Pages: 36
Harman AMX ENOVA DVX-3250HD-SP Instruction Manual preview
AMX ENOVA DVX-3250HD-SP
Brand: Harman Pages: 119
Ruby Tech GS-2108C User Manual preview
GS-2108C
Brand: Ruby Tech Pages: 254
3Com 3C16895 Installation Manual preview
3C16895
Brand: 3Com Pages: 74
Alpha Cordex HP CXRF 48-2.4kW Manual preview
Cordex HP CXRF 48-2.4kW
Brand: Alpha Pages: 56
Hubner EGS 2 Operating And Assembly Instructions Manual preview
EGS 2
Brand: Hubner Pages: 23
ETS SM8-RC Instructions preview
SM8-RC
Brand: ETS Pages: 2
socomec SIRCO 27DC3011 Quick Start Manual preview
SIRCO 27DC3011
Brand: socomec Pages: 6
Alps Electric SKRN Series Specifications preview
SKRN Series
Brand: Alps Electric Pages: 4
Linksys SRW2024P User Manual preview
SRW2024P
Brand: Linksys Pages: 110
Analog way Smart MatriX LE User Manual preview
Smart MatriX LE
Brand: Analog way Pages: 56
Microsens MS453510M User Manual preview
MS453510M
Brand: Microsens Pages: 42
Rolls ABY32 Owner'S Manual preview
ABY32
Brand: Rolls Pages: 2
Manhattan 151245 Instructions preview
151245
Brand: Manhattan Pages: 2
Ltech LT-424-MC Quick Start Manual preview
LT-424-MC
Brand: Ltech Pages: 2
Moxa Technologies EDS-2005-EL Series Quick Installation Manual preview
EDS-2005-EL Series
Brand: Moxa Technologies Pages: 14
GarrettCom Hubs User Manual preview
Hubs
Brand: GarrettCom Pages: 12

Brands by name

Popular brands

Load more brands