Command reference
R&S
®
ZNA
1020
User Manual 1178.6462.02 ─ 20
'BP2G1/A1G1' | ... 'BP02G1/A01G1' | ... 'B2G1/
AP1G1SAM' | 'B2G1/AP1G1RMS' | 'BP2G1/
AP1G1PEAK' | 'BP2G1/AP1G1AVG' | ...
Ratio of primed/unprimed wave quantities with port numbers and external
generator providing the stimulus signal (G<no> for generator no.). The
strings SAM, RMS, PEAK, AVG appended to the wave quantities denote a
normal (sample), RMS, peak, or average detector.
'IMB21' | 'IMB12' | 'IMB31' | ...
Imbalance parameter Imb<receive_port><drive_port> for logical port num-
bers <receive_port> and <drive_port>. The logical ports must be different
and at least one of them must be balanced.
'CMRR11' | 'CMRR21' | 'CMRR12' | 'CMRR22' | ...
Common mode rejection ratio CMRR<receive_port><drive_port> parameter
for logical port numbers <receive_port> and <drive_port>, at least one of
them balanced.
'IMB1-23' | 'IMB23-1' | 'IMB1-24' | ...
Differential Imbalance parameters between a balanced and two single-ended
logical ports
'KFAC21' | 'KFAC12' | ...
Stability factor K (for unbalanced ports only)
'MUF121' | 'MUF112' | ...
Stability factor 1 (for unbalanced ports only)
'MUF221' | 'MUF212' | ...
Stability factor 2 (for unbalanced ports only)
'Pmtr1G1' | 'Pmtr2G1' | 'Pmtr3D1' | ...
Power sensor measurement using a power meter 'Pmtr<no>' and either an
external generator 'G<no>' or an analyzer source port 'D<no>'
'PAE21' | PAE12' | ...
Power added efficiency (referring to logical ports)
'IM3UI' | 'IM3UO' | 'IM3LI' | 'IM3LO' | 'IM3MI' |
'IM3MO' | 'IM5UI' ... 'IM9MO'
Intermodulation product IM<order><side><at DUT> where <order> = 3 | 5 | 7
| 9, <side> = U | L | M (for upper or lower or major), <at DUT> = I | O (for
input or output)
'IM3UIR' | 'IM3UOR' | 'IM3LIR' | 'IM3LOR' | 'IM3MIR'
| 'IM3MOR' | 'IM5UIR' ... 'IM9MOR'
Intermodulation product (as explained above) displayed in dB units
r
elative
to the measured lower tone level at DUT input or output ("intermodulation
suppression")
'IP3UI' | 'IP3UO' | 'IP3LI' | 'IP3LO' | 'IP3MI' | 'IP3MO'
| 'IP5UI' ... 'IP9MO'
Intercept point IP<order><side><at DUT> where <order> = 3 | 5 | 7 | 9,
<side> = U | L | M (for upper or lower or major), <at DUT> = I | O (for input or
output)
UTI | UTO | LTI | LTO
Upper or lower tone at DUT input or output
NLO
Noise level at DUT output
Requires option R&S
ZNA-K30.
'NF12' | 'NF13' | ... | 'NF21' | 'NF23' | ...
Noise figure parameters NF<out><in>, where <out> and <in> denote the
output and input port numbers of the DUT, and <out>≠<in>.
Requires option R&S
ZNA-K30.
'b1/a2(P2)' | 'b1/a3(P3)' | ... | 'b2/a1(P1)' | 'b2/
a3(P3)' | ...
Gain of the DUT, as measured in noise figure channels
'NF1R' | 'NF2R' | ...
Receiver noise figure, as measured in noise figure channels
'SA1' | 'SA2' | ...
Spectrum trace at the measurement receiver ofport 1, 2, ...
Requires option R&S
ZNA-K1.
'SA1REF' | 'SA2REF' | ...
Spectrum trace at the reference receiver of port 1, 2, ...
Requires option R&S
ZNA-K1.
'CmpPtPin' | 'CmpPtPout' | 'CmpPtS'
Compression point traces for gain compression measurements:
power in | power out | S-param
SCPI command reference