Omron R88D-KN01H-ECT-L страница 415 Скачать руководство пользователя | Manualshive

Страница: 415 / 626

background image

12 - 5

12 Troubleshooting and Maintenance

G5-series Linear Motors/Servo Drives With Built-in EtherCAT Communications

12-

2 War

n

ing

s

12

12-

2-1

Rela

ted Ob

jects

12-2 Warnings

This function outputs a warning signal and notifies state such as an overload before an error occurs.

Set whether to hold warning state by setting the Warning Hold Selection (3759 hex). If not holding
warnings is selected, a warning will be cleared automatically when the cause of the warning has been
eliminated.

If holding warnings is selected, the normal procedure to clear errors must be performed after removing
the cause of the error.

12-2-1 Related Objects

Index

Name

Description

Reference

3440 hex

Warning Output

Selection 1

Select the warning for Warning Output 1 (WARN1).

0: Output for all warnings.

1 or higher: Refer to 12-2-2 Warning List on page 12-6.

3441 hex

Warning Output

Selection 2

Select the warning for Warning Output 2 (WARN2).

0: Output for all warnings.

1 or higher: Refer to 12-2-2 Warning List on page 12-6.

3638 hex

Warning Mask

Setting

Set a mask for warning detection. If you set the
corresponding bit to “1”, the detection of the
corresponding warning is disabled.

For details, refer to 12-2-2 Warning List on page 12-6.

3759 hex

bit 0

Warning Hold

Selection for

Communications-

related Warnings

Select whether to hold servo-related and
communications-related warning state.

0: Do not hold

1: Hold

bit 1

Warning Hold

Selection for

General

Warnings

3781 hex

Data Setting

Warning

Detection Setting

Set how many times the EtherCAT communications
data setting warning should be detected continuously
without an error.

If a data setting warning (Warning No. B0 hex) occurs
more than this setting, a Command Error (Error No.
91.1) will occur.

3800 hex

Communications

Control

Controls errors and warnings related to EtherCAT
communications.

If you set the corresponding bit to “1”, the detection of
the corresponding warning is disabled.

«
...
413
414
415
416
417
...
»

Содержание R88D-KN01H-ECT-L



















































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для R88D-KN01H-ECT-L

ACH580-01 Series

Бренд: ABB Страницы: 8

Бренд: ABB Страницы: 2

Бренд: Parker Страницы: 103

L-force EWS0069

Бренд: Lenze Страницы: 12

Бренд: iRZ Страницы: 134

Бренд: Carotron Страницы: 28

Terra HP Generation 3 CE

Бренд: ABB Страницы: 96

Бренд: ABB Страницы: 20

Advanced Line SP+ 075 ATEX MC

Бренд: Wittenstein Alpha Страницы: 52

Бренд: GSK Страницы: 88

CompletePower Plus CPP-A24V80A-SA-CAN

Бренд: ElectroCraft Страницы: 47

Бренд: Chauvin Arnoux Страницы: 64

Бренд: Grundfos Страницы: 140

Бренд: ZIEHL-ABEGG Страницы: 72

Бренд: Stanley Страницы: 52

Sonesse Ultra 50 RTS

Бренд: SOMFY Страницы: 52

Бренд: Eurotherm Drives Страницы: 42

Бренд: Ridder Страницы: 52

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды