manualshive.com logo in svg

Omron CJ1G-CPUxx, Instructions Manual

Share
Download
Omron CJ1G-CPUxx Instructions Manual Download Page 260

239

Timer and Counter Instructions

Section 3-6

Description

CNR(545)/CNRX(547) resets the Completion Flags of all timers or counters
from N

1

 to N

2

. At the same time, the PVs will all be set to the maximum value

(9999 for BCD and FFFF for binary). (The PV will be set to the SV the next
time that the timer or counter instruction is executed.)

Timers Reset by CNR(545)/CNRX(547)
The following timers will be reset if their timer numbers fall within the specified
range: TIM, TIMX(550), TIMH(015), TIMHX(551), TMHH(540), TMHHX(552),
TTIM(087), TTIMX(555), TIMW(813), TIMWX(816), TMHW(815), and
TMHWX(817). When a timer is reset, its Completion Flag is turned OFF and
its PV is set to the maximum value of 9999.

Note The TIML(542), TIMLX(553), MTIM(543), and MTIMX(554) timers are not

reset by CNR(545)/CNRX(547) because these timers do not use timer num-
bers.

Counters Reset by CNR(545)/CNRX(547)
The following counters will be reset if their counter numbers fall within the
specified range: CNT, CNTX(546), CNTR(012), CNTRX(548), CNTW(814),
and CNTWX(818). When a counter is reset, its Completion Flag is turned
OFF and its PV is set to the maximum value of 9999.

Flags

Precautions

CNR(545)/CNRX(547) doesn’t reset the timer/counter instructions them-
selves, it resets the PVs and Completion Flags allocated to those instructions.
In most cases, the effect of CNR(545)/CNRX(547) is different from directly
resetting the instructions. For example, when a TIM/TIMX(550) instruction is
reset directly its PV is set to the SV, but when that timer is reset by CNR(545)/
CNRX(547) its PV is set to the maximum value of 9999.

When N1 and N2 are specified with N1>N2, only the Completion Flag for the
timer/counter number will be reset.

Example

When CIO 000000 is ON in the following example, the Completion Flags for
timers T0002 to T0005 are turned OFF and the timers’ PVs are set to the
maximum value of 9999.

Constants

---

---

Data Registers

---

---

Index Registers

---

---

Indirect addressing 
using Index Registers

,IR0 to ,IR15

–2048 to +2047 ,IR0 to –2048 to +2047 ,IR15

DR0 to DR15, IR0 to IR15

,IR0+(++) to ,IR15+(++)

,–(– –)IR0 to, –(– –)IR15

Area

N

1

N

2

Name

Lab-

el

Operation

Error Flag

ER

ON if N

1

 is indirectly addressed through an Index Register but the 

address in the Index Register is not the PV address of a timer or 
counter.

ON if N

2

 is indirectly addressed through an Index Register but the 

address in the Index Register is not the PV address of a timer or 
counter.

ON if N

1

 and N

2

 are not in the same data area.

OFF in all other cases.

Summary of Contents for CJ1G-CPUxx

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands