manualshive.com logo in svg

Omron CJ1G-CPUxx, Instructions Manual

Share
Download
Omron CJ1G-CPUxx Instructions Manual Download Page 190

169

Sequence Output Instructions

Section 3-4

Variations

Note Immediate refreshing is not supported by the CS1D CPU Units.

Applicable Program Areas

Operand Specifications

Description

When S turns ON, the designated bit will go ON and stay ON until reset,
regardless of whether S stays ON or goes OFF. When R turns ON, the desig-
nated bit will go OFF. The relationship between execution conditions and
KEEP(011) bit status is shown below.

Variations

Executed Each Cycle for ON Condition

KEEP(011)

Executed Once for Upward Differentiation

Not supported

Executed Once for Downward Differentiation

Not supported

Immediate Refreshing Specification (See note.)

!KEEP(011)

Block program areas

Step program areas

Subroutines

Interrupt tasks

Not allowed

OK

OK

OK

Area

B

CIO Area

CIO 000000 to CIO 614315

Work Area

W00000 to W51115

Holding Bit Area

H00000 to H51115

Auxiliary Bit Area

A44800 to A95915

Timer Area

---

Counter Area

---

DM Area

---

EM Area without bank

---

EM Area with bank

---

Indirect DM/EM 
addresses in binary 

---

Indirect DM/EM 
addresses in BCD

---

Constants

---

Data Registers

---

Index Registers

---

Indirect addressing 
using Index Registers

,IR0 to ,IR15

–2048 to +2047, IR0 to –2048 to +2047, IR15

DR0 to DR15, IR0 to IR15

,IR0+(++) to ,IR15+(++)

,–(– –) IR0 to, –(– –) IR15

Set

Reset

Summary of Contents for CJ1G-CPUxx

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands