Omron CJ1G-CPUxx Instructions Manual Download Page 165

Page: 165 / 1144

144

Sequence Input Instructions

Section 3-3

Example

3-3-2

LOAD NOT: LD NOT

Purpose

Indicates a logical start and creates an ON/OFF execution condition based on
the reverse of the ON/OFF status of the specified operand bit.

Ladder Symbol

Variations

Note

The following variations are supported by only the CS1-H, CJ1-H, or CJ1M
CPU Units: @LD NOT, %LD NOT, !@LD NOT, and !%LD NOT.

Immediate refresing is not supported by the CS1D CPU Units.

Applicable Program Areas

Instruction

Operand

000000

000001

000002

AND

000003

OR LD

---

AND LD

---

LD NOT

000004

AND

000005

OR LD

---

OUT

000100

OR LD

AND LD

OR LD

Bus bar

Starting point of block

Variations

Restarts Logic and Creates ON Each Cycle Operand
Bit is OFF

LD NOT

Restarts Logic and Creates ON Once for Upward
Differentiation (See note 1.)

@LD NOT

Restarts Logic and Creates ON Once for Downward
Differentiation (See note 1.)

%LD NOT

Immediate Refreshing Specification (See note 2.)

!LD NOT

Combined
Variations

Refreshes Input Bit, Restarts Logic, and Creates ON
Once for Upward Differentiation (See note 1.)

!@LD NOT

Refreshes Input Bit, Restarts Logic, and Creates ON
Once for Downward Differentiation (See note 1.)

!%LD NOT

Block program areas

Step program areas

Subroutines

Interrupt tasks

Summary of Contents for CJ1G-CPUxx

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for CJ1G-CPUxx

Reviews:

Brands by name

Popular brands

Omron CJ1G-CPUxx, Instructions Manual

Search results

Summary of Contents for CJ1G-CPUxx

Reviews:

Brands by name

Popular brands