Huawei SmartAX MA5616 Configuration Manual Download

Page: 10 / 553

7.8.1 Configuring the Device Authentication.................................................................................................306

7.8.1.1 Configuring the Device Authentication (Based on the H.248 Protocol)......................................306
7.8.1.2 Configuring the Device Authentication (Based on the SIP Protocol)..........................................308

7.8.2 Configuring the Dual Homing...............................................................................................................309

7.8.2.1 Configuring the Dual Homing (Based on the H.248 Protocol)....................................................309
7.8.2.2 Configuring the Dual Homing (Based on the SIP Protocol)........................................................310

7.8.3 Configuring the Emergency Standalone................................................................................................312

8 Configuration Example of Services on the MA5616 Through GPON Upstream
Transmission.................................................................................................................................314

8.1 Configuration Example of the xDSL Internet Access Service.......................................................................315

8.1.1 Configuration Example of the xDSL Internet Access Service Through PPPoE Dialup.......................315
8.1.2 Configuration Example of the xDSL IPoE Internet Access Service.....................................................322
8.1.3 Configuration Example of the xDSL PPPoA Internet Access Service..................................................328
8.1.4 Configuration Example of the xDSL IPoA Internet Access Service.....................................................335

8.2 Configuration Example of the Multicast Service (Multicast VLAN Mode)..................................................341

8.2.1 Configuration Example of the Multicast Video Service (Static Configuration Mode).........................342
8.2.2 Configuration Example of the Multicast Video Service (Dynamic Generation Mode)........................346

8.3 Configuration Example of the VoIP Service..................................................................................................350

8.3.1 Configuration Example of the VoIP PSTN Service (Based on the H.248 Protocol)............................350
8.3.2 Configuration Example of the VoIP PSTN Service (Based on the SIP Protocol)................................358
8.3.3 Configuration Example of the VoIP ISDN BRA Service.....................................................................361

8.4 Configuration Example of the VLAN Stacking Wholesale Service..............................................................368

8.4.1 Configuration Example of the VLAN Stacking Wholesale Service.....................................................368
8.4.2 Configuration Example of the VLAN ID Extension Service................................................................372

8.5 Configuring the Triple Play Service...............................................................................................................376

9 Configuration Example of Services on the MA5616 Through GE Upstream Transmission
..........................................................................................................................................................397

9.1 Configuration Example of the xDSL Internet Access Service.......................................................................398

9.1.1 Configuration Example of the xDSL Internet Access Service Through PPPoE Dialup.......................398
9.1.2 Configuration Example of the xDSL IPoE Internet Access Service.....................................................405
9.1.3 Configuration Example of the xDSL PPPoA Internet Access Service..................................................412
9.1.4 Configuration Example of the xDSL IPoA Internet Access Service.....................................................419

SmartAX MA5616 Multi-service Access Module
Configuration Guide

Contents

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

Summary of Contents for SmartAX MA5616










































































































































































































































































































































































































































































































































































Search results

Summary of Contents for SmartAX MA5616

Reviews:

Related manuals for SmartAX MA5616

Brands by name

Popular brands

Huawei SmartAX MA5616, Configuration Manual

Search results

Summary of Contents for SmartAX MA5616

Reviews:

Related manuals for SmartAX MA5616

Brands by name

Popular brands