manualshive.com logo in svg

Huawei SmartAX MA5616, Configuration Manual

The Huawei SmartAX MA5616 Configuration Manual is a detailed and comprehensive guide that enables users to efficiently set up and optimize their Huawei SmartAX MA5616. Easily downloadable for free from manualshive.com, this manual provides step-by-step instructions and essential information to maximize your product experience.

Share
Download
background image

Parameter

Remarks

code

The coding modes of the MG interface and
the MGC must be the same. Currently, only
text coding mode is supported.

transfer

The transmission mode is selected according
to the requirements of the MGC. Generally,
UDP is used.

start-negotiate-version

If the MGC connecting to the MG is a Huawei
device, the profile (parameter profile-index)
does not need to be set; if the MGC
connecting to the MG is a device of another
vendor, the profile (parameter profile-index)
must be set (the parameter value is prompted
on the CLI).
If the profile file in the system cannot meet
requirements, contact Huawei for technical
support.

 

Step 3

Check whether the attribute of the MG interface is the same as that in the data plan.

Run the 

display if-h248 attribute

 command to check whether the attribute of the MG interface

is the same as that in the data plan.

----End

Example

Assume that the MG interface ID is 0, the H.248 protocol is used for interconnecting with the
MGC, the signaling IP address is 10.13.4.116, the transport layer protocol port ID is 2944, IP
address 1 of the primary MGC is 10.13.2.118, the transport layer protocol port ID of the primary
MGC is 2944, media IP address 1 is 10.71.46.69, media IP address 2 is 10.13.4.117, the H.248
protocol version is started to be negotiated based on the profile, the transaction reliability is
enabled. To add such an MG interface, do as follows:

huawei(config)#

interface h248 0

  Are you sure to add MG interface?(y/n)[n]:

y

huawei(config-if-h248-0)#

if-h248 attribute  mgip 10.13.4.116 mgport 2944 code text

primary-mgc-ip1 10.13.2.118 primary-mgc-port 2944 mg-media-ip1 10.71.46.69
mg-media-ip2 10.13.4.117 start-negotiate-version 0 retrans enable

huawei(config-if-h248-0)#

display if-h248 attribute

-------------------------------------------------
  MGID                                  0
  MG Description                        -
  MG DomainName                         -
  Protocol                              H248
  Start Negotiate Version               0
  Profile Negotiation Parameter         Disable
  Profile index                         1:NoProfile("")
  2833Encrypt                           -
  Codetype                              Text
  Transfer Mode                         -
  HeartBeatGenTimer(s)                  60
  HeartBeatRetransTimes                 3
  HeartBeatRetransTimer(s)              60
  MG signalling IP                      10.13.4.116

SmartAX MA5616 Multi-service Access Module
Configuration Guide

7 Configuring the Voice Service

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

216

Summary of Contents for SmartAX MA5616










































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SmartAX MA5616

H3C S5120V3-EI Series Manual preview
S5120V3-EI Series
Brand: H3C Pages: 54
Ublox LENA-R8 Series System Integration Manual preview
LENA-R8 Series
Brand: Ublox Pages: 116
H3C CR16000-M Installation Manual preview
CR16000-M
Brand: H3C Pages: 116
Matrox Millennium P650 User Manual preview
Millennium P650
Brand: Matrox Pages: 54
Paradyne 7510 DSU Start-Up Instructions preview
7510 DSU
Brand: Paradyne Pages: 10
Xircom RealPort Ethernet 10/100 User Manual preview
RealPort Ethernet 10/100
Brand: Xircom Pages: 30
Tektronix CTS 850 User Manual preview
CTS 850
Brand: Tektronix Pages: 178
Netis DL4305D Quick Installation Manual preview
DL4305D
Brand: Netis Pages: 16
Intel BLKDP45SG - MB 1333FSB DDR3 1333 Aud+Lan RAID SATA ATX Product Manual preview
BLKDP45SG - MB 1333FSB DDR3 1333 Aud+Lan RAID SATA ATX
Brand: Intel Pages: 86
Pressalit Care Indivo RK1010 User And Maintenance Manual preview
Indivo RK1010
Brand: Pressalit Care Pages: 31
Supermicro AOC-STG-I2 User Manual preview
AOC-STG-I2
Brand: Supermicro Pages: 15
Ista AMF2.0 Operator'S Manual preview
AMF2.0
Brand: Ista Pages: 16
Sierra Wireless AirCard 750 Installation preview
AirCard 750
Brand: Sierra Wireless Pages: 2
Teridian 71M6533 Quick Start Manual preview
71M6533
Brand: Teridian Pages: 2
B+B SmartWorx Airborne M2M ABDN-er-DP55 Series User Manual preview
Airborne M2M ABDN-er-DP55 Series
Brand: B+B SmartWorx Pages: 120
DigiTech RP 3 User Manual preview
RP 3
Brand: DigiTech Pages: 28
Tenda FH456 User Manual preview
FH456
Brand: Tenda Pages: 82
ST METERS AND MORE UM2241 User Manual preview
METERS AND MORE UM2241
Brand: ST Pages: 26

Brands by name

Popular brands

Load more brands