Huawei SmartAX MA5616 Configuration Manual Download | Manualshive

Page: 26 / 553

background image

l

Baud rate: 9600 bit/s

l

Data bit: 8

l

Parity: None

l

Stop bit: 1

l

Flow control: None

NOTE

l

The baud rate of the HyperTerminal must be the same as that of the serial port on the MA5616. By
default, the baud rate of the serial port on the MA5616 is 9600 bit/s.

l

There may be illegible characters in the displayed input information after you log in to the system. This
is because the baud rates between the HyperTerminal and the MA5616 are not the same. In this case,
set a different baud rate to log in to the system. The system supports the baud rates of 9600 bit/s, 19200
bit/s, 38400 bit/s, 57600 bit/s, and 115200 bit/s.

Figure 3-5

Setting the parameters of the HyperTerminal

Click

OK

, and the HyperTerminal interface is displayed, as shown in

.

SmartAX MA5616 Multi-service Access Module
Configuration Guide

3 Basic Configuration

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

15

«
...
24
25
26
27
28
...
»

Summary of Contents for SmartAX MA5616










































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SmartAX MA5616

Express Ethernetwork DI-704P

Brand: D-Link Pages: 17

AllShare Cast Dongle

Brand: Samsung Pages: 2

Brand: D-Link Pages: 14

Brand: D-Link Pages: 7

Brand: D-Link Pages: 41

Brand: QNAP Pages: 20

Brand: Edge-Core Pages: 7

Brand: IBM Pages: 32

JetWeb JX2-PR0FI1

Brand: Jetter Pages: 67

Brand: Genie Pages: 15

Brand: Acces I/O products Pages: 5

SINUS H PROFInet

Brand: Enertronica Santerno Pages: 34

LBON320AC Series

Brand: Lindsay Broadband Pages: 4

Brand: Selta Pages: 83

Brand: Z3 Technology Pages: 67

Brand: Abocom Pages: 63

Brand: AXAGO Pages: 2

Brand: EMTRUST Pages: 103

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands