Huawei SmartAX MA5616 Configuration Manual Download | Manualshive

Page: 321 / 553

background image

Procedure

Step 1

In global config mode, run the

interface h248

command to enter the MG interface mode.

Step 2

Run the

mg-software parameter 2

command to configure the MG interface to support the dual

homing.

----End

Example

To configure MG interface 0 to support the dual homing, and not to automatically switch over
to the active MGC when the active MGC recovers, do as follows:

huawei(config)#

interface h248 0

huawei(config-if-h248-0)#

mg-software parameter 2 1

huawei(config-if-h248-0)#

display mg-software parameter 2

-------------------------------------------------
Interface Id:0 para index:2 value:1
-------------------------------------------------
APPENDIX:
-------------------------------------------------
Interface software parameter name:
2: Whether MG support dual-home function
0: Do not support the dual-homing
1: Support the dual-homing, but do not support the auto switchover
2: Support the dual-homing and auto switchover

Related Operation

lists the related operation for configuring the dual homing when the H.248 protocol

is used.

Table 7-32

Related operation for configuring the dual homing (H.248)

To...

Run the Command...

Forcibly switch the MG to register with the
other MGC

mgc switch

7.8.2.2 Configuring the Dual Homing (Based on the SIP Protocol)

The SIP dual-homing means that the MA5616 supports the 1+1 mutual assistance mode of the
upstream P-CSCF/PROXY, namely, the deployment in the active/standby mode. When one of
the upstream active/standby devices is faulty, the MA5616 service automatically switches to
another device, thus implementing the disaster recovery for the access reliability of the device
when the SIP protocol is used.

Prerequisites

On the IMS, the data for interconnecting with the SIP interface must be configured.

SmartAX MA5616 Multi-service Access Module
Configuration Guide

7 Configuring the Voice Service

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

310

«
...
319
320
321
322
323
...
»

Summary of Contents for SmartAX MA5616










































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SmartAX MA5616

Express Ethernetwork DI-704P

Brand: D-Link Pages: 2

Power Xpert Meter 2000

Brand: Eaton Pages: 16

POW-R-COMMAND 1000

Brand: Eaton Pages: 84

QSR-3920 Series

Brand: QTech Pages: 120

Brand: QSC Pages: 28

Brand: Amperes Pages: 8

Brand: Pima Pages: 4

Brand: Tripp Lite Pages: 2

Brand: Gate Pages: 8

IntroSpect Analyzer 2 Series

Brand: Aruba Pages: 5

Brand: E-Lins Pages: 113

Brand: Selta Pages: 83

Brand: Sangoma Pages: 6

Brand: PMD Pages: 74

Brand: Caton Pages: 18

RADEON 9800 PRO

Brand: ATI Technologies Pages: 20

Brand: Nortel Pages: 163

Brand: Baracoda Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands