Huawei SmartAX MA5616 Configuration Manual Download | Manualshive

Page: 428 / 553

background image

----------------------------------------------------------------------------
Total Num : 7

According to service requirement, the user access rate is 2048 kbit/s. The query result shows
that traffic profile 5 meets the requirement.

NOTE

l

If no traffic profile in the system meets the service requirement, run the

traffic table ip

command to

configure a new traffic profile.

l

On the MA5616, the user access rate can be limited by either a traffic profile or a VDSL line profile.
When both profiles are configured, the user bandwidth adopts the minimum value in the two profiles.
In this example, the traffic profile is used to limit the user access rate.

4.

Run the

service-port

command to create a service port. The index of the new service virtual

port is 3, the access port is port 0/1/0, traffic profile 5 meets the service requirement, and
the S-VLAN is VLAN 50. The VPI and VCI must be the same as the management VPI and
VCI of the peer modem. Assume that the management VPI and VCI of the modem are 1
and 39. To facilitate the maintenance of the service port, also configure the service port
description.

huawei(config)#

service-port 3 vlan 50 vdsl mode atm 0/1/0 vpi 1 vci 39 inbound

traffic-table index 5 outbound
traffic-table index 5

huawei(config)#

service-port desc 3 description MA5616HW/Vlanid:50/vdsl/smart

5.

Set the maximum number of MAC addresses that can be learned by the service port is 16.
This parameter is to limit the maximum number of the MAC addresses that can be learned
by one account, namely the maximum number of the PCs that can access the Internet
through one account.

huawei(config)#

mac-address max-mac-count service-port 3 16

Step 6

Configure the PPPoA-PPPoE protocol conversion.

This step is to configure the PPPoA MAC address pool. The start MAC address in the MAC
address pool is 0000-1111-1010, and the maximum number of the MAC addresses in the MAC
address pool is 300. The PPPoA-PPPoE protocol conversion is enabled and the service
encapsulation mode is LLC.

huawei(config)#

mac-pool xpoa 0000-1111-1010 300

huawei(config)#

pppoa enable

huawei(config)#

encapsulation 0/2/0 vpi 1 vci 39 type pppoa llc

huawei(config)#

encapsulation 0/4/0 vpi 1 vci 39 type pppoa llc

huawei(config)#

encapsulation 0/1/0 vpi 1 vci 39 type pppoa llc

Step 7

Configure the user account security.

The PITP P mode can be enabled to protect the user account against theft and roaming. The
RAIO mode can be customized according to actual requirements. Here, the

cntel

is considered

as an example.

huawei(config)#

pitp enable pmode

huawei(config)#

raio-mode cntel pitp-pmode

NOTE

For details about the PITP configuration for the user account security, see

3.10.1 Configuring Anti-Theft and

Roaming of User Account Through PITP

Step 8

Save the data.

huawei(config)#

save

----End

SmartAX MA5616 Multi-service Access Module
Configuration Guide

9 Configuration Example of Services on the MA5616

Through GE Upstream Transmission

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

417

«
...
426
427
428
429
430
...
»

Summary of Contents for SmartAX MA5616










































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SmartAX MA5616

Brand: Xantrex Pages: 8

Brand: LAWO Pages: 154

Brand: VAF instruments Pages: 56

Brand: Oracle Pages: 112

Supero SAS-826A

Brand: Supero Pages: 16

Brand: XNET Pages: 17

Brand: Toto Link Pages: 55

Brand: Renesas Pages: 941

PCMCIA High Speed Serial Card CE 232HSPCC

Brand: B&B Electronics Pages: 14

Brand: Camozzi Pages: 22

Brand: Omnia Pages: 130

System 200V PC 288

Brand: VIPA Pages: 54

Brand: NovaStar Pages: 16

Brand: ADTRAN Pages: 4

Kontron OSM-S i.MX8M Mini

Brand: S&T Pages: 41

Brand: Lanner Pages: 80

Brand: Lanner Pages: 116

Brand: LinMot Pages: 62

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands