manualshive.com logo in svg

Huawei SmartAX MA5616, Configuration Manual

The Huawei SmartAX MA5616 Configuration Manual is a detailed and comprehensive guide that enables users to efficiently set up and optimize their Huawei SmartAX MA5616. Easily downloadable for free from manualshive.com, this manual provides step-by-step instructions and essential information to maximize your product experience.

Share
Download
background image

l

For the meaning of each character in the digitmap body, see the Context in 

7.1.1.4

(Optional) Configuring the Digitmap of an MG Interface

.

Precaution

l

When the H.248 protocol is used, the type of the local digitmap can only be normal.

l

When the SIP protocol is used, the type of the local digitmap can be normal, emergency,
scc, direct-centrex, or second-centrex. For the meaning of the digitmap type, see the
Parameter Description in the 

local-digitmap add

 command.

Procedure

Step 1

In privilege mode, run the 

display protocol support

 command to query the current protocol

type used on the MA5616.

l

When the H.248 protocol is used, go to 

Step 5

.

l

When the SIP protocol is used, go to 

Step 2

.

Step 2

In privilege mode, run the 

display local-digitmap

 command to query the default local digitmap.

l

If the default local digitmap can meet the requirements, the configuration is complete.

l

If the default local digitmap cannot meet the requirements, perform one or more operations
in 

Step 3

, 

Step 4

, and 

Step 5

 to configure a proper local digitmap.

Step 3

Run the 

local-digitmap modify

 command to change the name, type, or body of the local

digitmap.

Step 4

Run the 

local-digitmap append

 command to add a digitmap body in the local digitmap.

Step 5

According to the data plan, run the 

local-digitmap add

 command to add a local digitmap.

Step 6

Run the 

display local-digitmap

 command to check whether the local digitmap is the same as

the planned local digitmap.

----End

Example

Assume that the H.248 protocol is used on the MA5616. To add a local digitmap with the data
listed in 

Table 7-17

, do as follows:

Table 7-17

 Local digitmap existing in the system

Digitmap Name

Digitmap Type

Digitmap Body

huawei

normal

([2-8]xxxxxxx|[2-8]
xxSxxxxxxx|13xxxxxxxxx|
0xxxxxxxxx|9xxxx|1
[0124-9]x|F|x.F|[0-9].S)

 

huawei(config)#

local-digitmap add huawei normal ([2-8]xxxxxxx|[2-8]xxSxxxxxxx|13

xxxxxxxxx|0xxxxxxxxx|9xxxx|1[0124-9]x|F|x.F|[0-9].S)

huawei(config)#

display local-digitmap all

  ------------------------------------------
  Name: huawei

SmartAX MA5616 Multi-service Access Module
Configuration Guide

7 Configuring the Voice Service

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

260

Summary of Contents for SmartAX MA5616










































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SmartAX MA5616

Ratoc Systems SmartMedia Adapter PC Card REX-SMA01F Product Manual preview
SmartMedia Adapter PC Card REX-SMA01F
Brand: Ratoc Systems Pages: 75
Renesas F-ZTAT H8/3048 Series User Manual preview
F-ZTAT H8/3048 Series
Brand: Renesas Pages: 34
Google AC-1304 User Manual preview
AC-1304
Brand: Google Pages: 14
process-informatik CONNECT Series Operation Quick Start Manual preview
CONNECT Series
Brand: process-informatik Pages: 8
Paradyne 7510 DSU Start-Up Instructions preview
7510 DSU
Brand: Paradyne Pages: 10
Cervoz MEC-COM-2032i User Manual preview
MEC-COM-2032i
Brand: Cervoz Pages: 22
Nvidia Quadro M6000 Sync User Manual preview
Quadro M6000 Sync
Brand: Nvidia Pages: 8
Silicon Systems SiliconDrive SSD-P16G(I)-3100 Datasheet preview
SiliconDrive SSD-P16G(I)-3100
Brand: Silicon Systems Pages: 108
ZALMAN ZM-2HC2 User Manual preview
ZM-2HC2
Brand: ZALMAN Pages: 8
Paradyne JetFusion 2100 Series User Manual preview
JetFusion 2100 Series
Brand: Paradyne Pages: 296
Dataprobe iBoot Instruction Manual preview
iBoot
Brand: Dataprobe Pages: 16
ZyXEL Communications GS1100-10HP User Manual preview
GS1100-10HP
Brand: ZyXEL Communications Pages: 30
TP-Link Archer MR600 User Manual preview
Archer MR600
Brand: TP-Link Pages: 113
VIA Technologies Mobile360 M810 Quick Start Manual preview
Mobile360 M810
Brand: VIA Technologies Pages: 25
Z3 Technology DM8168-MOD-35 Manual preview
DM8168-MOD-35
Brand: Z3 Technology Pages: 22
SIIG US2273 Quick Installation Manual preview
US2273
Brand: SIIG Pages: 8
Renesas M32173T-PTC User Manual preview
M32173T-PTC
Brand: Renesas Pages: 7
ActionTec GE344000-01 User Manual preview
GE344000-01
Brand: ActionTec Pages: 87

Brands by name

Popular brands

Load more brands