Huawei SmartAX MA5616 Configuration Manual Download | Manualshive

Page: 67 / 553

background image

VLA
N
Attri
bute

Configuration
Command

VLAN Type

VLAN
Description

Application
Scenario

VLA
N
Stacki
ng

To configure
stacking as the
attribute of a
VLAN, run the

vlan attrib vlanid
stacking

command.

The VLAN with
this attribute can
only be a smart
VLAN or a MUX
VLAN.

The packets from a
stacking VLAN
contain two VLAN
tags, that is, inner
VLAN tag and
outer VLAN tag
from the MA5616.
The upper-layer
BRAS
authenticates the
access users
according to the
two VLAN tags. In
this manner, the
number of access
users is increased.
On the upper-layer
network in the L2
working mode, a
packet can be
forwarded directly
by the outer VLAN
tag and MAC
address mode to
provide the
wholesale service
for ISPs.

Applicable to the
1:1 access scenario
for the wholesale
service or
extension of
VLAN IDs.
In the case of a
stacking VLAN, to
configure the tag of
the service port,
run the

stacking

label

command.

You can run the

stacking outer-
ethertype

command to set the
type of outer
Ethernet protocol
supported by
VLAN stacking on
the MA5616. You
can also run the

stacking inner-
ethertype

command to set the
type of inner
Ethernet protocol
supported by
VLAN stacking.
To ensure that
Huawei device is
interconnected
with the device of
other vendors, the
type of inner/outer
Ethernet protocol
must be the same as
that of the
interconnect
device.

SmartAX MA5616 Multi-service Access Module
Configuration Guide

3 Basic Configuration

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

56

«
...
65
66
67
68
69
...
»

Summary of Contents for SmartAX MA5616










































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SmartAX MA5616

Brand: Wattle Pages: 6

Brand: Baicells Pages: 8

ARM Cortex-A9 MPCore

Brand: Dave Embedded Systems Pages: 67

Brand: IEI Technology Pages: 19

Brand: IEI Technology Pages: 87

Brand: IEI Technology Pages: 3

Brand: Pakedge Device & Software Pages: 20

Brand: RadiSys Pages: 44

Brand: Commell Pages: 58

ADSL 2/2+ Router with USB Port ADE-3410v2

Brand: Planet Pages: 62

Brand: EVS Pages: 30

Brand: SIIG Pages: 6

Brand: IBASE Technology Pages: 71

Brand: Net to Net Technologies Pages: 4

FieldPoint cFP-RTD-122

Brand: National Instruments Pages: 15

kontron COMe-cEL6

Brand: S&T Pages: 99

DSL5068EN(1T1R)

Brand: Aztech Pages: 40

Brand: Parker Pages: 50

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands