Huawei SmartAX MA5616 Configuration Manual Download | Manualshive

Page: 381 / 553

background image

Item

Data

User 2:

l

Access port: 0/1/1

l

Inner VLAN tag: 12

ISP 2 user group

Uplink port: 0/0/1

Network-side VLAN ID (outer VLAN tag): 101

VLAN attribute: stacking VLAN

User 3:

l

Access port: 0/1/2

l

Inner VLAN tag: 11

User 4:

l

Access port: 0/1/3

l

Inner VLAN tag: 12

Procedure

Step 1

Create VLANs.

Network-side VLAN IDs are 100 and 101, and the VLAN type is smart VLAN.

huawei(config)#

vlan 100-101 smart

It will take several minutes, and console may be timeout, please use command
idle-timeout to set time limit
Are you sure to add VLANs? (y/n)[n]:

y

The total of the VLANs having been processed is 2
The total of the added VLANs is 2

Step 2

Set the VLAN attribute to stacking VLAN.

NOTE

You can run the

stacking outer-ethertype

command to set the type of outer Ethernet protocol supported

by VLAN stacking on the MA5616. You can also run the

stacking inner-ethertype

command to set the

type of inner Ethernet protocol supported by VLAN stacking on the MA5616. To ensure that Huawei device
is interconnected with the device of other vendors, the type of the inner/outer Ethernet protocol must be
the same as that of the interconnect device.

huawei(config)#

vlan attrib 100-101 stacking

It will take several minutes, and console may be timeout, please use command
idle-timeout to set time limit
Are you sure to continue? (y/n)[n]:

y

The total of the VLANs having been processed is 2
The total of the VLAN(s) which have been operated successfully is 2

Step 3

Add an uplink port to the VLAN.

Add uplink port 0/0/1 to VLAN 100 and VLAN 101.

huawei(config)#

port vlan 100-101 0/0 1

It will take several minutes, and console may be timeout, please use command
idle-timeout to set time limit
Are you sure to add standard port(s)? (y/n)[n]:

y

SmartAX MA5616 Multi-service Access Module
Configuration Guide

8 Configuration Example of Services on the MA5616

Through GPON Upstream Transmission

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

370

«
...
379
380
381
382
383
...
»

Summary of Contents for SmartAX MA5616










































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SmartAX MA5616

Brand: N-Tron Pages: 101

Express Ethernetwork DI-704P

Brand: D-Link Pages: 17

Brand: IBM Pages: 86

Brand: 2N Pages: 11

Brand: 2N Pages: 5

Brand: 2N Telekomunikace Pages: 24

Brand: Datasat Pages: 32

Ray 3 Plus Client

Brand: Sun Microsystems Pages: 6

Brand: Hama Pages: 10

Brand: Paradox Pages: 4

Brand: Javad Pages: 35

Brand: ebm-papst Pages: 16

Brand: LORD Pages: 9

Brand: Caimore Pages: 79

ACC-CX3RDK-CU5640

Brand: e-con Systems Pages: 9

Storagelibrary T24

Brand: Tandberg Data Pages: 28

Brand: Delta Electronics Pages: 1

Brand: TRENDnet Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands