Huawei SmartAX MA5616 Configuration Manual Download | Manualshive

Page: 517 / 553

background image

32303131B39FD641 snmp ont-lineprofile-id 10

huawei(config-if-gpon-0/2)#

ont confirm 1 ontid 2 sn-auth

32303131B39FD642 snmp ont-lineprofile-id 10

b.

(Optional) Bind an alarm profile to the ONU.
After an alarm profile is configured, bind it to the ONT. In this example, bind
the default alarm profile, namely alarm profile 1 to the ONU.

huawei(config-if-gpon-0/2)#

ont alarm-profile 1 1 profile-id 1

huawei(config-if-gpon-0/2)#

ont alarm-profile 1 2 profile-id 1

5.

Confirm that the ONU goes online normally.

NOTE

In this step, query the status of ONU 1 as an example. The same method is applied for querying the
status of ONU 2.

After an ONU is added, run the

display ont info

command to query the current status

of the ONU. Ensure that

Control flag

of the ONU is

active

,

Run State

is

online

, and

Config state

is

normal

.

huawei(config-if-gpon-0/2)#

display ont info 1 1

---------------------------------------------------------------------

F/S/P :
0/2/1
ONT-ID :
1
Control flag :

active

//Indicates that the ONU is

activated.
Run state :

online

//Indicates that the ONU already goes

online normally.
Config state :

normal

//Indicates that the configuration status

of the ONU is normal.

...//The rest of the response information is omitted.

If the ONU state fails, the ONU fails to be in the up state, or the ONU does not match,
refer to the following suggestions to rectify the fault.

–

If

Control flag

is

deactive

, run the

ont activate

command in the GPON port mode

to activate the ONU.

–

If the ONU fails to be in the up state, that is,

Run state

is

offline

, the physical line

may be broken or the optical transceiver may be damaged. You need to check both
the material and the line.

–

If the ONU state fails, that is,

Config state

is

failed

, the ONU capability set

outmatches the actual ONU capabilities. In this case, run the

display ont failed-

configuration

command in the diagnosis mode to check the failed configuration

item and the failure cause. Then, rectify the fault according to actual conditions.

NOTE

If an ONT supports only four queues, the values of 4-7 of the priority-queue parameter in the

gem add

command are invalid. After configuration recovers, Config state will be failed.

6.

Configure the management channel from the OLT to the ONU.

a.

Configure the inband management VLAN and IP address of the OLT.
To telnet to the ONU from the OLT and then configure the ONU, you need to
configure the inband management VLANs and IP addresses of the OLT and the
ONU on the OLT.
Create management VLAN 8, and configure the inband management IP address
to 192.168.50.1/24.

SmartAX MA5616 Multi-service Access Module
Configuration Guide

10 Configuration Examples of the FTTx

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

506

«
...
515
516
517
518
519
...
»

Summary of Contents for SmartAX MA5616










































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SmartAX MA5616

Ray 3 Plus Client

Brand: Sun Microsystems Pages: 6

Brand: Juniper Pages: 502

Brand: NETGEAR Pages: 2

Brand: Freescale Semiconductor Pages: 921

Brand: Paradyne Pages: 85

PG-FlexPlus AMU-912

Brand: ADC Pages: 130

Brand: Fieldbus Specialists Pages: 39

Brand: LevelOne Pages: 31

SteelCentral NetExpress

Brand: Riverbed Pages: 38

LinkSmart KW6515

Brand: Kasda Pages: 31

FireWire 800 + Hi-Speed USB Combo

Brand: SIIG Pages: 20

Speedway Revolution

Brand: impinj Pages: 60

HiGain H2TU-R-402 List 7A

Brand: ADC Pages: 7

Brand: Renesas Pages: 28

Brand: TP-Link Pages: 87

Brand: LevelOne Pages: 26

Brand: Supermicro Pages: 15

Brand: ekwb Pages: 11

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands