manualshive.com logo in svg

Huawei SmartAX MA5616, Configuration Manual

The Huawei SmartAX MA5616 Configuration Manual is a detailed and comprehensive guide that enables users to efficiently set up and optimize their Huawei SmartAX MA5616. Easily downloadable for free from manualshive.com, this manual provides step-by-step instructions and essential information to maximize your product experience.

Share
Download
background image

Step 6

Configure the security of user accounts.
Assume that the RAIO mode is the user-defined mode, the CID is the access node name frame/
slot/port:vlanid, the RID is the label of the service port where the user is connected. To enable
the DHCP option 82 function with these parameters, do as follows:

huawei(config)#

dhcp option82 enable

huawei(config)#

raio-mode user-defined dhcp-option82

huawei(config)#

raio-format dhcp-option82 cid anid frame/slot/port:vlanid

huawei(config)#

raio-format dhcp-option82 rid splabel

NOTE

l

For the details about the security of DHCP accounts, see 

3.10.2 Configuring Anti-Theft and Roaming of

User Accounts Through DHCP

.

Step 7

Save the data.

huawei(config)#

save

----End

Verification

l

Step 1: After the PC NIC automatically obtains an IP address and a connection to the
Internet is set up, the user can access the Internet.

l

Step 2: To download a file through FTP, open 

Windows Task Manager

 and then click

Networking

 to observe the link rate. Calculate the Internet access rate by the formula:

attainable Internet access rate = computer NIC rate/48 x 53 x 8. The calculated result
approximates to the planned 2048 kbit/s.

Configuration File

Configuration File for the ADSL access mode:

vlan 50 smart  
vlan attrib 50 stacking 
vlan service-profile profile-id 1
forwarding vlan-connect
commit
quit
vlan bind service-profile 50 profile-id 1
port vlan 50 0/0 0
interface adsl 0/2
deactivate 0
activate 0 template-index 1
alarm-config 0 1
quit
service-port 1 vlan 50 adsl 0/2/0 vpi 1 vci 39 inbound traffic-table index 5 
outbound traffic-table index 5 
service-port desc 1 description Vlanid:50/adsl/vpi:1vci:39/stacking
stacking label service-port 1 10
stacking inner-priority service-port 1 4
dhcp option82 enable
raio-mode user-defined dhcp-option82
raio-format dhcp-option82 cid anid frame/slot/port:vlanid
raio-format dhcp-option82 rid splabel
save

Configuration File for the SHDSL access mode:

vlan 50 smart  
vlan attrib 50 stacking 
vlan forwarding 50 vlan-connect
port vlan 50 0/0 0
shdsl line-profile quickadd 3 ptm rate 512 2048 

SmartAX MA5616 Multi-service Access Module
Configuration Guide

8 Configuration Example of Services on the MA5616

Through GPON Upstream Transmission

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

327

Summary of Contents for SmartAX MA5616










































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SmartAX MA5616

Paradyne 3163 Quick Reference preview
3163
Brand: Paradyne Pages: 16
Mackie SP260 Installation Instructions preview
SP260
Brand: Mackie Pages: 2
Mackie SP260 Product Overview preview
SP260
Brand: Mackie Pages: 5
Harman Kardon CITATION 7.0 Owner'S Manual preview
CITATION 7.0
Brand: Harman Kardon Pages: 66
NavigateWorx NR300 User Manual preview
NR300
Brand: NavigateWorx Pages: 71
ETAS FETK-S2.1 User Manual preview
FETK-S2.1
Brand: ETAS Pages: 69
Blackrock Microsystems Cerebus Instructions For Use Manual preview
Cerebus
Brand: Blackrock Microsystems Pages: 27
ZyXEL Communications P-336M Specifications preview
P-336M
Brand: ZyXEL Communications Pages: 2
Omega Engineering OME-A8111 Hardware Manual preview
OME-A8111
Brand: Omega Engineering Pages: 34
Teknim TWM-1886 Installation & User Manual preview
TWM-1886
Brand: Teknim Pages: 10
Parker ACR1200 Hardware Manual preview
ACR1200
Brand: Parker Pages: 50
Dolphin IBP-G4x16-2 User Manual preview
IBP-G4x16-2
Brand: Dolphin Pages: 9
TP-Link Archer MR500 User Manual preview
Archer MR500
Brand: TP-Link Pages: 110
ebm-papst D3G146-LT13-30 Operating Instructions Manual preview
D3G146-LT13-30
Brand: ebm-papst Pages: 11
YASKAWA PG-Z2 Instructions Manual preview
PG-Z2
Brand: YASKAWA Pages: 15
DAD DXZ48 User Manual preview
DXZ48
Brand: DAD Pages: 16
Addonics Technologies ADSA2 Installation Manual preview
ADSA2
Brand: Addonics Technologies Pages: 1
Parker PCH1 T P Series User Manual preview
PCH1 T P Series
Brand: Parker Pages: 107

Brands by name

Popular brands

Load more brands