Huawei SmartAX MA5616 Configuration Manual Download

Page: 55 / 553

Table 3-5

Configuration principles of uplink and cascaded ports on an MA5616

Control Board

Daughter Board
on the Control
Board

Configuration Principles

CCUB

GP1A

GE port 0: is set as a cascaded or uplink port.

GPON port: is always set as an uplink port.

EP1A

GE port 0: is set as a cascaded or uplink port.

EPON port: is always set as an uplink port.

GE1A

GE port 0: is set as a cascaded or uplink port.

GE port 1: is always set as an uplink port.

Default configuration

Table 3-6

lists the default settings of the attributes of an Ethernet port.

Table 3-6

Default settings of the attributes of an Ethernet port

Parameter

Default Setting (Optical Port)

Default Setting (Electrical
Port)

Auto-negotiation
mode of the port

Disabled

Enabled

Port rate

GE optical port: 1000 Mbit/s

NOTE

After the auto-negotiation mode
of the port is disabled, you can
configure the port rate.

Duplex mode

Full-duplex

NOTE

After the auto-negotiation mode
of the port is disabled, you can
configure the duplex mode.

Network cable
adaptation mode

Not supported

FE electrical port: auto

GE electrical port: normal

Flow control

Disabled

Procedure

Configure the physical attributes of an Ethernet port.

(Optional) Set the auto-negotiation mode of the Ethernet port.
Run the

auto-neg

command to set the auto-negotiation mode of the Ethernet port. You

can enable or disable the auto-negotiation mode:

SmartAX MA5616 Multi-service Access Module
Configuration Guide

3 Basic Configuration

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

Summary of Contents for SmartAX MA5616










































































































































































































































































































































































































































































































































































Search results

Summary of Contents for SmartAX MA5616

Reviews:

Related manuals for SmartAX MA5616

Brands by name

Popular brands

Huawei SmartAX MA5616, Configuration Manual

Search results

Summary of Contents for SmartAX MA5616

Reviews:

Related manuals for SmartAX MA5616

Brands by name

Popular brands