Huawei SmartAX MA5616 Configuration Manual Download | Manualshive

Page: 538 / 553

background image

huawei(config)#

queue-scheduler wrr 10 10 20 20 40 0 0 0

Configure the mapping between the queues and 802.1p priorities. Priorities 0-7 map
queues 0-7 respectively.

huawei(config)#

cos-queue-map cos0 0 cos1 1 cos2 2 cos3 3 cos4 4 cos5 5 cos6

6 cos7 7

11. Save the data.

huawei(config)#

save

l

Configure the ONU.

NOTE

The configuration on ONU 1 and ONU 2 is the same. Take configuration on ONU 1 for example.

1.

Log in to the ONU to perform the configuration.
On the OLT, use the management IP address of the ONU to log in to the ONU through
Telnet. User name:

root

(default). Password:

mduadmin

(default).

2.

Configure the upstream port of the media stream and the signaling stream.
Create VLAN 200 and add upstream port 0/0/1 (0/9/0 for MA5603T) to the VLAN.
Configure the IP address of the VLAN Layer 3 interface to 17.10.10.10 and subnet
mask to 255.255.0.0.

NOTE

l

The VLAN ID must be consistent with the CVLAN of the OLT.

l

The VLAN ID of the default upstream Ethernet port is 1. Use the default VLAN if no
specific VLAN is required for the upstream transmission.

l

If you need to use another VLAN to transmit packets in the upstream direction, run the

port vlan

command to add the specified upstream port to the VLAN.

huawei(config)#

vlan 200 smart

huawei(config)#

port vlan 200 0/0 1

//for MA5616

huawei(config)#

port vlan 200 0/9 0

//for MA5603T

huawei(config)#

interface vlanif 200

huawei(config-if-vlanif200)#

ip address 17.10.10.10 24

huawei(config-if-vlanif200)#

quit

3.

Configure the media and signaling IP address pools.
Configure both the media IP address, the signaling IP address to 17.10.10.10 and the
media gateway address to 17.10.10.1.

huawei(config)#

voip

huawei(config-voip)#

ip address media 17.10.10.10 17.10.10.1

huawei(config-voip)#

ip address signaling 17.10.10.10

huawei(config-voip)#

quit

NOTE

l

You can configure the attributes of the SIP interface only when the media IP address and
the signaling IP address exist in the media and signaling IP address pools.

l

The media IP address and the signaling IP address can be different. You can plan the IP
addresses according to the actual network.

4.

Configure the static route.
Because the IP address of the VLAN interface and the IP address of the IMS are in
different network segments, you should configure a route for the network segment
from gateway 17.10.10.1 to 200.200.200.0.

huawei(config)#

ip route-static 200.200.200.0 24 17.10.10.1

5.

Add an SIP interface.
Add SIP interface 0.

SmartAX MA5616 Multi-service Access Module
Configuration Guide

10 Configuration Examples of the FTTx

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

527

«
...
536
537
538
539
540
...
»

Summary of Contents for SmartAX MA5616










































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SmartAX MA5616

Brand: Ubiquiti Pages: 24

Brand: Samsung Pages: 2

Brand: Samsung Pages: 31

Brand: Samsung Pages: 15

Brand: Harmonic Pages: 56

Brand: Accusys Pages: 34

Brand: Patton electronics Pages: 12

Brand: Justec Pages: 61

Brand: UfiSpace Pages: 35

Brand: Point of View Pages: 13

Super Sound Set SR-JV80-07

Brand: Roland Pages: 8

Brand: Schrack Technik Pages: 2

PISO-725 Series

Brand: ICP DAS USA Pages: 8

Brand: Marani Pages: 39

Brand: ebm-papst Pages: 13

Brand: IEI Technology Pages: 136

Brand: Modecom Pages: 16

Brand: Teldat Pages: 23

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands