Huawei SmartAX MA5616 Configuration Manual Download | Manualshive

Page: 218 / 553

background image

l

Dual homing
Supports dual homing from the MG to the MGC through the H.248 protocol and
authentication from the SIP AG to the SIP proxy server through the SIP protocol.

NOTE

In this document, the MG, AG, gateway, or SIP AG refers to the MA5616, unless otherwise stated.

The voice pre-configuraiton profile of the MA5616 supports the configuration of main voice
parameters through a single command.

l

Run the

voice-para-template

command to select the parameter profile for an area to

quickly configure the voice service. Run the

display voice-para-template(sip)

and

display

voice-para-template(H248)

commands to query the parameter configurations for different

areas.

l

When the parameter configurations defined in the system do not meet the requirements,
run the

userdef-template-port-para

command to modify the parameter configurations in

the user defined parameter profile.

l

If you do not use the voice configuration profile, configure the voice parameters one by
one by following the configuration steps in the next topics.

7.1 Configuring the VoIP PSTN Service (Based on the H.248 Protocol)

This topic describes how to configure the VoIP PSTN service on the MA5616 when the H.248
protocol is used.

7.2 Configuring the VoIP PSTN Service (Based on the SIP Protocol)

This topic describes how to configure the VoIP PSTN service on the MA5616 through the
Session Initiation Protocol (SIP).

7.3 Configuring the VoIP ISDN BRA Service

This topic describes how to configure the VoIP ISDN BRA service on an IP network. When the
MA5616 uses the H.248 protocol, the device supports the access of the ISDN BRA user. ISDN
technology provides end-to-end (E2E) digital connection and supports multiple types of voice
and non-voice telecom services.

7.4 Configuring the FoIP Service (Based on the H.248 Protocol)

This topic describes how to configure the FoIP service when the H.248 protocol is used to
transmit the fax data service over the IP network.

7.5 Configuring the FoIP Service (Based on the SIP Protocol)

This topic describes how to configure the FoIP service based on the SIP protocol to transmit the
fax data service over the IP network.

7.6 Configuring the MoIP Service (Based on the H.248 Protocol)

This topic describes how to configure the MoIP service when the H.248 protocol is used to
transmit the modem data service over the IP network.

7.7 Configuring the MoIP Service (Based on the SIP Protocol)

This topic describes how to configure the MoIP service when the SIP protocol is used to transmit
the modem data service over the IP network.

7.8 Configuring the Security and Reliability of the Voice Service

For the MA5616, the security configuration of the voice service includes the H.248-based, or
SIP-based device authentication configuration. The reliability configuration of the voice service
includes the dual-homing configuration and the emergency standalone configuration.

SmartAX MA5616 Multi-service Access Module
Configuration Guide

7 Configuring the Voice Service

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

207

«
...
216
217
218
219
220
...
»

Summary of Contents for SmartAX MA5616










































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SmartAX MA5616

Brand: Ebyte Pages: 8

Brand: JCG Pages: 2

Brand: Furuno Pages: 24

tBOX330-870-FL Series

Brand: AXIOMTEK Pages: 2

Brand: Funkwerk Pages: 2

PG-FLEX RT FRL-752

Brand: PairGain Pages: 6

NVIP- NVRA0104/GO

Brand: Novus Pages: 44

Brand: Radicom Pages: 27

WGR614 - Wireless-G Router Wireless

Brand: NETGEAR Pages: 116

NIC-FC730i-Mb-2-32G

Brand: H3C Pages: 37

Brand: AOpen Pages: 18

GSM7224v2 - Layer 2 Managed Gigabit Switch

Brand: NETGEAR Pages: 3

RP614 - Web Safe Router

Brand: NETGEAR Pages: 16

Brand: MiWire Pages: 24

E5345 - Xeon 2.33 GHz 8M L2 Cache 1333MHz FSB LGA771 Active Quad-Core Processor

Brand: Intel Pages: 112

Brand: Hama Pages: 7

X-FireWire Card

Brand: Apogee Pages: 32

Brand: nox Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands