Huawei SmartAX MA5616 Configuration Manual Download | Manualshive

Page: 507 / 553

background image

–

Automatically find an ONU: If the password or SN of an ONU is unknown,
run the

port ont-auto-find

command in the GPON mode to enable the ONU

auto-find function of the GPON port. Then, run the

ont confirm

command

to confirm the ONU.

To add an ONU offline, do as follows:

huawei(config)#

interface gpon 0/2

huawei(config-if-gpon-0/2)#

ont add 1 ontid 1 sn-auth

32303131B39FD641
snmp ont-lineprofile-id 10

huawei(config-if-gpon-0/2)#

ont add 1 ontid 2 sn-auth

32303131B39FD642
snmp ont-lineprofile-id 10

To automatically find an ONU, do as follows:

huawei(config)#

interface gpon 0/2

huawei(config-if-gpon-0/2)#

port 1 ont-auto-find enable

huawei(config-if-gpon-0/2)#

display ont autofind 1

---------------------------------------------------------------------
---
Number : 1
F/S/P : 0/2/1
Ont SN : 32303131B39FD641
Password :
Loid : 0000000000
Checkcode :
VenderID : HWTC
Ont Version : MA5616 VER.B
Ont SoftwareVersion : V8R309 C00
Ont EquipmentID : SmartAX MA5616
Ont autofind time : 2011-05-10 10:06:00+08:00

---------------------------------------------------------------------
---
Number : 2
F/S/P : 0/2/1
Ont SN : 32303131B39FD642
Password :
Loid : 0000000000
Checkcode :
VenderID : HWTC
Ont Version : MA5616 VER.B
Ont SoftwareVersion : V8R309 C00
Ont EquipmentID : SmartAX MA5616
Ont autofind time : 2011-05-10 10:06:00+08:00

---------------------------------------------------------------------
---
huawei(config-if-gpon-0/2)#

ont confirm 1 ontid 1 sn-auth

32303131B39FD641 snmp ont-lineprofile-id 10

huawei(config-if-gpon-0/2)#

ont confirm 1 ontid 2 sn-auth

32303131B39FD642 snmp ont-lineprofile-id 10

b.

(Optional) Bind an alarm profile to the ONU.

After an alarm profile is configured, bind it to the ONT. In this example, bind
the default alarm profile, namely alarm profile 1 to the ONU.

huawei(config-if-gpon-0/2)#

ont alarm-profile 1 1 profile-id 1

huawei(config-if-gpon-0/2)#

ont alarm-profile 1 2 profile-id 1

5.

Confirm that the ONU goes online normally.

NOTE

In this step, query the status of ONU 1 as an example. The same method is applied for querying the
status of ONU 2.

SmartAX MA5616 Multi-service Access Module
Configuration Guide

10 Configuration Examples of the FTTx

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

496

«
...
505
506
507
508
509
...
»

Summary of Contents for SmartAX MA5616










































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SmartAX MA5616

Brand: Paradyne Pages: 16

Power Xpert Meter 2000

Brand: Eaton Pages: 16

POW-R-COMMAND 1000

Brand: Eaton Pages: 84

Brand: Patton electronics Pages: 75

RocketLink-G 3088/I

Brand: Patton electronics Pages: 61

Brand: Patton Pages: 12

Brand: Patton Pages: 84

OnSite 3210 Series

Brand: Patton Pages: 110

Brand: Patton electronics Pages: 2

SMARTNODE 4110 Series

Brand: Patton electronics Pages: 78

Brand: Patton electronics Pages: 8

Brand: Qlogic Pages: 2

Brand: Qlogic Pages: 172

Brand: MiLAN Pages: 1

PacketShaper PS-S200

Brand: Symantec Pages: 2

Brand: Belkin Pages: 72

Brand: Helmholz Pages: 28

kontron COMe-cEL6

Brand: S&T Pages: 99

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands