Huawei SmartAX MA5616 Configuration Manual Download | Manualshive

Page: 144 / 553

background image

Item

Data

Remarks

Name of digital parameter 2:
Arrester

This digital parameter is set according to the
actual requirements. The monitoring digital
parameter of the lightning arrester status
sensor is set to monitor the arrester status.

User-defined alarm ID of
digital parameter 2: 2

When the lightning arrester is faulty, the
MA5616 reports an alarm.

Digital parameter ID: 3

In the F01S50 cabinet, digital parameter 3
does not take effect. In the F01S100 cabinet,
digital parameter 3 is used to monitor the
MDF.

Valid level of digital
parameter 3: low level

When the low level represents the valid level,
the MA5616 does not report an alarm in the
case of low level.

Name of digital parameter 3:
Fan

This digital parameter is set according to the
actual requirements. The monitoring digital
parameter of the fan status sensor is set to
monitor the fan status.

User-defined alarm ID of
digital parameter 3: 5

When the fan is faulty, the MA5616 reports
an alarm.

huawei(config)#

display emu 0

EMU ID: 0
----------------------------------------------------------------------------
EMU name : H831VESC
EMU type : H831VESC
Used or not : Used
EMU state : Normal
Frame ID : 0
Subnode : 1
COM port : -
----------------------------------------------------------------------------
huawei(config)#

interface emu 0

huawei(config-if-h831vesc-0)#

esc digital 0 available-level low-level digital-alarm

5 name Temperature

huawei(config-if-h831vesc-0)#

esc digital 1 available-level high-level digital-

alarm 1 name Door

huawei(config-if-h831vesc-0)#

esc digital 2 available-level low-level digital-alarm

2 name Arrester

huawei(config-if-h831vesc-0)#

esc digital 3 available-level low-level digital-alarm

5 name Fan

huawei(config-if-h831vesc-0)#

display esc environment info

EMU ID: 0 ESC environment state
---------------------------Digital environment info-------------------------
ID Name State Value |ID Name State Value
0 Temperature Normal 0 |1 Door Alarm 0
2 Arrester Normal 0 |3 Fan Normal 0
----------------------------------------------------------------------------
huawei(config-if-h831vesc-0)#

quit

huawei(config)#

save

SmartAX MA5616 Multi-service Access Module
Configuration Guide

3 Basic Configuration

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

133

«
...
142
143
144
145
146
...
»

Summary of Contents for SmartAX MA5616










































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SmartAX MA5616

BB-HGW700A - Network Camera Router

Brand: Panasonic Pages: 10

Brand: Paradyne Pages: 16

Brand: Datasat Pages: 32

OXTOPUS EIA-709

Brand: OCCITALINA Pages: 54

Brand: NETGEAR Pages: 14

Brand: EVS Pages: 30

Brand: SIIG Pages: 6

Emulator MCU Board for 38D5 Group M38D59T-RLFS

Brand: Renesas Pages: 4

PCard-E 021L-D5 Series

Brand: ORiNG Pages: 2

Brand: Zhone Pages: 2

Brand: National Instruments Pages: 26

PXI Terminal Block NI TB-2709

Brand: National Instruments Pages: 12

Brand: Sony Ericsson Pages: 2

Brand: Alesis Pages: 11

CyberPower RMCARD201

Brand: CyberPower Pages: 8

Brand: NXP Semiconductors Pages: 1202

Brand: Cypress Semiconductor Pages: 9

Brand: Acces Pages: 21

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands