Huawei SmartAX MA5616 Configuration Manual Download | Manualshive

Page: 528 / 553

background image

You can run the

display traffic table ip

command to query the traffic profiles existing

in the system. If the traffic profiles existing in the system do not meet the requirements,
you need to run the

traffic table ip

command to add a traffic profile.

Add traffic profile 9, and no rate limitation on user packets. The priority is 6 and the
priority policy is scheduled by the priority that the packets bear.

huawei(config)#

traffic table ip index 9 cir off priority 6 priority-policy

tag-In-Package

9.

Create a service port.

Create service port 200 connected to ONU 1 and service port 201 connected to ONU
2. SVLAN ID to 200, GEM port ID to 1, bind traffic profile 9 and CVLAN ID to 200.

NOTE

The CVLAN must be consistent with the upstream VLAN of the ONU.

huawei(config)#

service-port 200 vlan 200 gpon 0/2/1 ont 1 gemport 1 multi-

service user-vlan 200 rx-cttr 9 tx-cttr 9

huawei(config)#

service-port 201 vlan 200 gpon 0/2/1 ont 2 gemport 1 multi-

service user-vlan 200 rx-cttr 9 tx-cttr 9

10. Configure the queue scheduling mode.

Adopt the 3PQ+5WRR queue scheduling. Queues 0-4 adopt the WRR mode and their
weights are 10, 10, 20, 20, and 40 respectively. Queues 5-7 adopt the PQ mode. The
priority of the VoIP service is 6, adopting the PQ mode.

NOTE

l

The queue scheduling mode is configured globally, and you need to configure it only once on
the OLT. After the configuration is complete, the queue scheduling mode takes effect globally.
When subsequent services are configured, you need not configure the queue scheduling mode
again.

l

For a board that supports only four queues, the mapping between the 802.1p priorities and queue
IDs are as follows: priorities 0 and 1 map queue 1; priorities 2 and 3 map queue 2; priorities 4
and 5 map queue 3; priorities 6 and 7 map queue 4.

huawei(config)#

queue-scheduler wrr 10 10 20 20 40 0 0 0

Configure the mapping between the queues and 802.1p priorities. Priorities 0-7 map
queues 0-7 respectively.

huawei(config)#

cos-queue-map cos0 0 cos1 1 cos2 2 cos3 3 cos4 4 cos5 5 cos6

6 cos7 7

11. Save the data.

huawei(config)#

save

l

Configure the ONU.

NOTE

The configuration on ONU 1 and ONU 2 is the same. Take configuration on ONU 1 for example.

1.

Log in to the ONU to perform the configuration.
On the OLT, use the management IP address of the ONU to log in to the ONU through
Telnet. User name:

root

(default). Password:

mduadmin

(default).

2.

Configure the upstream port of the media stream and the signaling stream.
Create VLAN 200 and add upstream port 0/0/1 (0/9/0 for MA5603T) to the VLAN.
Configure the IP address of the VLAN Layer 3 interface to 17.10.10.10 and subnet
mask to 255.255.255.0,

SmartAX MA5616 Multi-service Access Module
Configuration Guide

10 Configuration Examples of the FTTx

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

517

«
...
526
527
528
529
530
...
»

Summary of Contents for SmartAX MA5616










































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SmartAX MA5616

Brand: Cambium Networks Pages: 68

Brand: Cambium Networks Pages: 110

Brand: IEI Technology Pages: 187

Brand: IEI Technology Pages: 71

Brand: Black Box Pages: 9

Brand: Fostex Pages: 20

Brand: IOtech Pages: 16

Brand: Supermicro Pages: 16

PCI-6110E/6111E

Brand: National Instruments Pages: 113

Brand: Zhone Pages: 2

Brand: National Instruments Pages: 26

Brand: Lantronix Pages: 75

Brand: Rosco Pages: 20

Brand: ICS ELECTRONICS Pages: 4

Brand: Ebyte Pages: 23

Brand: H3C Pages: 34

Brand: LevelOne Pages: 142

Brand: ORiNG Pages: 101

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands