Huawei SmartAX MA5616 Configuration Manual Download | Manualshive

Page: 349 / 553

background image

index<K> }:


Command:
display traffic table ip from-index
0

----------------------------------------------------------------------------
TID CIR(kbps) CBS(bytes) PIR(kbps) PBS(bytes) Pri Copy-policy Pri-
Policy

----------------------------------------------------------------------------
0 1024 34768 2048 69536 6 - tag-
pri
1 2496 81872 4992 163744 6 - tag-
pri
2 512 18384 1024 36768 0 - tag-
pri
3 576 20432 1152 40864 2 - tag-
pri
4 64 4048 128 8096 4 - tag-
pri
5 2048 67536 4096 135072 0 - tag-
pri
6 off off off off 0 - tag-
pri

----------------------------------------------------------------------------
Total Num : 7

According to service requirement, the user access rate is 2048 kbit/s. The query result shows
that traffic profile 5 meets the requirement.

NOTE

l

If no traffic profile in the system meets the service requirement, run the

traffic table ip

command to

configure a new traffic profile.

l

On the MA5616, the user access rate can be limited by either a traffic profile or an SHDSL line profile.
When both profiles are configured, the user bandwidth adopts the minimum value in the two profiles.
In this example, the traffic profile is used to limit the user access rate.

4.

Run the

service-port

command to create a service port. The index of the new service virtual

port is 2, the access port is port 0/4/0, traffic profile 5 meets the service requirement, and
the S-VLAN is VLAN 50. The VPI and VCI must be the same as the management VPI and
VCI of the peer modem. Assume that the management VPI and VCI of the modem are 1
and 39. To facilitate the maintenance of the service port, also configure the service port
description.

huawei(config)#

service-port 2 vlan 50 shdsl mode atm 0/4/0 vpi 1 vci 39 inbound

traffic-table index 5 outbound
traffic-table index 5

huawei(config)#

service-port desc 2 description MA5616HW/Vlanid:50/shdsl/smart

5.

Set the maximum number of MAC addresses that can be learned by the service port is 16.
This parameter is to limit the maximum number of the MAC addresses that can be learned
by one account, namely the maximum number of the PCs that can access the Internet
through one account.

huawei(config)#

mac-address max-mac-count service-port 2 16

Step 5

In the case of the VDSL access mode, follow this procedure.

In this example, the VDSL normal mode is used as an example. For how to configure a VDSL
profile in the VDSL TI mode, see

3.7.3.2 Configuring the VDSL2 Profile (TI Mode)

1.

Configure a VDSL profile. For details, see

3.7.3.1 Configuring the VDSL2 Profile

(Normal Mode)

. Assume that the VDSL profile ID is 3, downstream rate is 2048 kbit/s,

channel mode is the interleave mode, maximum downstream interleave delay is 8 ms,

SmartAX MA5616 Multi-service Access Module
Configuration Guide

8 Configuration Example of Services on the MA5616

Through GPON Upstream Transmission

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

338

«
...
347
348
349
350
351
...
»

Summary of Contents for SmartAX MA5616










































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SmartAX MA5616

Brand: Hal Communications Pages: 25

Brand: Abocom Pages: 1

Brand: Campbell Pages: 42

Brand: LaCie Pages: 44

LaCie Ethernet Disk

Brand: LaCie Pages: 2

SATA II ExpressCard 34

Brand: LaCie Pages: 2

12big Rack Fibre 8

Brand: LaCie Pages: 9

Brand: Quick Eagle Networks Pages: 4

Brand: LORD Pages: 9

Optane M Series

Brand: Intel Pages: 59

Brand: DAD Pages: 32

Brand: Phytec Pages: 53

Brand: ZyXEL Communications Pages: 2

Brand: Dahua Pages: 24

Brand: EnGenius Pages: 3

PoleVault System A/V Source Inputs

Brand: Extron electronics Pages: 4

Brand: axing Pages: 52

Media Board D/120JCT-LS-EW

Brand: Dialogic Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands