Huawei SmartAX MA5616 Configuration Manual Download | Manualshive

Page: 449 / 553

background image

Item

Data

User priority

Users are common users, and the user
priority uses the default priority,
namely, cat3.

User type

Users are common users, and the user
type uses the default user type, namely,
DEL.

System Parameters

According to the Context in

(Optional) Configuring the System
Parameters

and confirmed with the

engineers of the office, the default
configuration can meet the service
requirements. Therefore, the system
parameters are not configured.

Overseas Parameters

According to the Context in

(Optional) Configuring the Overseas
Parameters

and confirmed with the

engineers of the office, the default
configuration can meet the service
requirements. Therefore, the overseas
parameters are not configured.

CAUTION

By
default,
these
parameter
s need not
be
configure
d if the H.
248
protocol
is used.
You can
configure
these
parameter
s
according
to the
requireme
nts.

Digitmap name

huawei

Digitmap type

Only the normal digitmap is supported
if the H.248 protocol is used.

Digitmap body

Plan this parameter according to the
prefix of the local phone number. In this
example, the ([2-8]xxxxxxx|[2-8]
xxSxxxxxxx|13xxxxxxxxx|
0xxxxxxxxx) digitmap body is used.

Attributes of a PSTN Port

The polarity reversal charging is
required for the service. Therefore, you
need to configure the PSTN port to
which the user belongs so that the PSTN
port supports the polarity reversal
impulse. The other attributes of the
PSTN port need not be modified.

SmartAX MA5616 Multi-service Access Module
Configuration Guide

9 Configuration Example of Services on the MA5616

Through GE Upstream Transmission

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

438

«
...
447
448
449
450
451
...
»

Summary of Contents for SmartAX MA5616










































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SmartAX MA5616

Brand: Laird Pages: 36

Brand: Octavo Pages: 28

Brand: Obihai Pages: 2

Brand: Watchguard Pages: 24

ER3-100 (5K02-55)

Brand: 8e6 Technologies Pages: 74

Brand: Abocom Pages: 1

Brand: ZKTeco Pages: 68

PCM-4141 Series

Brand: Advantech Pages: 96

X-NUCLEO-EEPRMA1

Brand: ST Pages: 22

Brand: Matrix Switch Corporation Pages: 54

Brand: ADTRAN Pages: 2

Brand: Aim Pages: 35

Brand: Hypercom Pages: 2

RouteFinder RF560VPN

Brand: Multitech Pages: 82

Brand: artisan Pages: 36

Brand: Alphacool Pages: 3

Brand: I-Tech Pages: 6

Brand: Moxa Technologies Pages: 94

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands