mask 255.255.255.0 gateway 192.168.50.254 vlan 8
huawei(config-if-gpon-0/2)#
quit
c.
Configure an inband management service port.
Configure the management service port index to 0, management VLAN ID to 8,
GEM port ID to 0, and CVLAN ID to 8. On the OLT, the rate of the inband
service port is not limited. Therefore, use default traffic profile 6. To limit the
rate of a service port, run the
traffic table ip
command to create a traffic profile
and then bind the profile to the service port.
huawei(config)#
service-port 1 vlan 8 gpon 0/2/1 ont 1 gemport 0 multi-
service
user-vlan 8 rx-cttr 6 tx-cttr 6
huawei(config)#
service-port 2 vlan 8 gpon 0/2/1 ont 2 gemport 0 multi-
service
user-vlan 8 rx-cttr 6 tx-cttr 6
7.
Confirm that the management channel between the OLT and the ONU is available.
–
On the OLT, run the
ping 192.168.50.2
and
ping 192.168.50.3
command to check
the connectivity to the ONU 1 and ONU 2. The ICMP ECHO-REPLY packet from
the ONU should be received.
–
You can run the
telnet 192.168.50.2
and
telnet 192.168.50.3
command to telnet
to the ONU 1 and ONU 2 and then configure the ONU.
8.
Configure the traffic profile.
You can run the
display traffic table ip
command to query the traffic profiles existing
in the system. If the traffic profiles existing in the system do not meet the requirements,
you need to run the
traffic table ip
command to add a traffic profile.
Add traffic profile 9, and no rate limitation on user packets. The priority is 6 and the
priority policy is scheduled by the priority that the packets bear.
huawei(config)#
traffic table ip index 9 cir off priority 6 priority-policy
tag-In-Package
9.
Create a service port.
Create service port 200 connected to ONU 1 and service port 201 connected to ONU
2. SVLAN ID to 200, GEM port ID to 1, bind traffic profile 9 and CVLAN ID to 200.
NOTE
The CVLAN must be consistent with the upstream VLAN of the ONU.
huawei(config)#
service-port 200 vlan 200 gpon 0/2/1 ont 1 gemport 1 multi-
service user-vlan 200 rx-cttr 9 tx-cttr 9
huawei(config)#
service-port 201 vlan 200 gpon 0/2/1 ont 2 gemport 1 multi-
service user-vlan 200 rx-cttr 9 tx-cttr 9
10. Configure the queue scheduling mode.
Adopt the 3PQ+5WRR queue scheduling. Queues 0-4 adopt the WRR mode and their
weights are 10, 10, 20, 20, and 40 respectively. Queues 5-7 adopt the PQ mode. The
priority of the VoIP service is 6, adopting the PQ mode.
NOTE
l
The queue scheduling mode is configured globally, and you need to configure it only once on
the OLT. After the configuration is complete, the queue scheduling mode takes effect globally.
When subsequent services are configured, you need not configure the queue scheduling mode
again.
l
For a board that supports only four queues, the mapping between the 802.1p priorities and queue
IDs are as follows: priorities 0 and 1 map queue 1; priorities 2 and 3 map queue 2; priorities 4
and 5 map queue 3; priorities 6 and 7 map queue 4.
SmartAX MA5616 Multi-service Access Module
Configuration Guide
10 Configuration Examples of the FTTx
Issue 04 (2011-10-30)
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
526
