Huawei SmartAX MA5616 Configuration Manual Download | Manualshive

Page: 373 / 553

background image

board, implementing the ISDN BRA service. The ISDN BRA service on the MA5616 can be
supported only by the H.248 protocol.

Prerequisites

l

The devices on the network must be connected properly and must work in the normal state.

l

The MA5616 must use the H.248 protocol to communicate with the MGC.

l

The data on the MGC side must be configured correctly.

l

NT1 must be connected properly and must work in the normal state.

Context

l

When the MG interface does not support the terminal layering, the terminal ID must be
configured and must be different from the terminal ID of an existing PSTN user.

l

When the MG interface supports terminal layering, the terminal ID cannot be configured,
and the system automatically allocates the terminal ID according to the TID profile
configured for the interface of the PSTN user.

l

You can run the

display tid-format

to query the TID profile to which various users under

the MG interface are bound, and then run the

display tid-template

command to check

whether the TID profile supports the layering configuration. Hence, you can check whether
the user supports terminal layering.

–

If the parameter list of the TID profile includes only keyword "G", it indicates that the
TID profile is used by the non-layering users. Users bound with this profile do not
support terminal layering.

–

If the parameter list of the TID profile includes only keywords "F", "S", "P", "B" ("B"
is unavailable for PSTN users), it indicates that the TID profile is used by the layering
users. Users bound with this profile support terminal layering.

Networking

shows the example network for configuring the ISDN BRA service.

SmartAX MA5616 Multi-service Access Module
Configuration Guide

8 Configuration Example of Services on the MA5616

Through GPON Upstream Transmission

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

362

«
...
371
372
373
374
375
...
»

Summary of Contents for SmartAX MA5616










































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SmartAX MA5616

Express EtherNetwork DFE-670TXD

Brand: D-Link Pages: 4

Brand: DAD Pages: 36

Brand: D-Link Pages: 2

S5500-HI Switch Series

Brand: H3C Pages: 180

Brand: H3C Pages: 84

Brand: H3C Pages: 281

Brand: H3C Pages: 8

Brand: H3C Pages: 9

Brand: H3C Pages: 33

Brand: H3C Pages: 42

Brand: H3C Pages: 102

S12500CR Series

Brand: H3C Pages: 9

Brand: H3C Pages: 15

H3C S7500E Series

Brand: H3C Pages: 1565

Brand: H3C Pages: 4

DesignCore RVP-TDA3 Series

Brand: D3 Pages: 34

RealPort Ethernet 10/100

Brand: Xircom Pages: 30

Brand: Tektronix Pages: 178

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands