Huawei SmartAX MA5616 Configuration Manual Download | Manualshive

Page: 401 / 553

background image

ice user-8021p 4 rx-cttr 9 tx-cttr 9
service-port 11 vlan 105 vdsl mode atm 0/1/1 vpi 0 vci 35 multi-serv
ice user-8021p 4 rx-cttr 9 tx-cttr 9
multicast-vlan 104
igmp mode proxy
y
igmp uplink-port 0/0/1
btv
igmp uplink-port-mode default
y
multicast-vlan 104
igmp program add name program1 ip 224.1.1.1 sourceip 10.10.10.10
igmp program add name program2 ip 224.1.1.2 sourceip 10.10.10.11
btv
igmp profile add profile-name profile0
igmp profile profile-name profile0 program-name program1 watch
igmp user add service-port 10
igmp user add service-port 11 auth
igmp user bind-profile service-port 11 profile-name profile0
multicast-vlan 104
igmp multicast-vlan member service-port 10
igmp multicast-vlan member service-port 11
quit
save

8.5.3 Configuring the Triple Play Service - Multiple PVCs for
Multiple Services

This topic describes how to configure the triple play service in the multi-PVC for multiple
services mode.

Prerequisites

Before configuring the triple play service, make sure that:

l

The network devices and lines are in the normal state.

l

The CPE is already configured (the CPE supports different PVCs for different services).

l

All boards of the device run in the normal state.

l

The VDSL2 line template and alarm template that are bound to the port are already
configured. For details on the configuration procedure, see

3.7.3 Configuring the VDSL2

Service Requirements

l

The MA5616 is used on the GPON upstream transmission network.

l

VDSL2 user 1 and VDSL2 user 2 are connected to the MA5616 to implement the triple
play.

l

The Internet service is provided in the PPPoE mode.

l

After receiving different traffic streams, the MA5616 provides different QoS guarantees
to the traffic streams according to the traffic priorities in the PVC.

Networking

Figure 8-16

shows the example network of the triple play service in the multi-PVC for multiple

services mode.

SmartAX MA5616 Multi-service Access Module
Configuration Guide

8 Configuration Example of Services on the MA5616

Through GPON Upstream Transmission

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

390

«
...
399
400
401
402
403
...
»

Summary of Contents for SmartAX MA5616










































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SmartAX MA5616

Brand: D-Link Pages: 5

Brand: D-Link Pages: 2

Brand: Abocom Pages: 1

Brand: E-Lins Pages: 59

Brand: E-Lins Pages: 11

Brand: E-Lins Pages: 9

Brand: E-Lins Pages: 5

Network Video Recorders

Brand: e-Line Technology Pages: 34

SR8800 IM-FW-II

Brand: H3C Pages: 107

Brand: 3Com Pages: 12

Brand: H3C Pages: 16

H3C S3600 Series

Brand: H3C Pages: 10

Brand: H3C Pages: 42

Brand: H3C Pages: 2

H3C S7500E Series

Brand: H3C Pages: 34

Brand: H3C Pages: 33

Brand: H3C Pages: 14

Brand: H3C Pages: 56

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands