Huawei SmartAX MA5616 Configuration Manual Download | Manualshive

Page: 389 / 553

background image

Table 8-8

Data plan of the triple play service based on the user-side VLAN

Item

Data

VDSE

Service ports: 0/1/0 and 0/1/1
Index of the VDSL2 line template bound to the port: 2, where:

l

Index of the VDSL2 line profile: 3

l

Index of the VDSL2 channel profile: 3

Index of the VDSL2 alarm template bound to the port: 2, where:

l

Index of the VDSL2 line alarm profile: 3

l

Index of the VDSL2 channel alarm profile: 3

VPI/VCI: 0/35

Traffic
profile
parameters

Internet service: 1 Mbit/s
VoIP service: 64 Kbit/s
IPTV service: no limit

Uplink port
ID

0/0/1

Upstream
VLANs

Internet service: smart VLAN 102
VoIP service: smart VLAN 103
IPTV service: smart VLAN 104

User-side
VLANs

Internet service: smart VLAN 2
VoIP service: smart VLAN 3
IPTV service: smart VLAN 4

IGMP
version

IGMP v3 (default IGMP version in the multicast VLAN mode)

Multicast
source

Two multicast sources:
ISP 1: with IP address 10.10.10.10, providing the multicast program with IP
address 224.1.1.1
ISP 2: with IP address 10.10.10.11, providing the multicast program with IP
address 224.1.1.2

Multicast
program
library

Programs in multicast VLAN 104:
Program 1: with IP address 224.1.1.1, the program source IP address being
the same as the IP address of ISP 1 (10.10.10.10)
Program 2: with IP address 224.1.1.2, the program source IP address being
the same as the IP address of ISP 2 (10.10.10.11)

Right profile

Set right profile 0. Profile 0 has the right to watch program 1 in the program
library.

Multicast
users

User 1: User 1 (on port 0/1/0) can watch all the programs.
User 2: User 2 (on port 0/1/1) can watch only program 1.

SmartAX MA5616 Multi-service Access Module
Configuration Guide

8 Configuration Example of Services on the MA5616

Through GPON Upstream Transmission

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

378

«
...
387
388
389
390
391
...
»

Summary of Contents for SmartAX MA5616










































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SmartAX MA5616

Brand: iDirect Pages: 60

Brand: Konig Pages: 73

Brand: ADTRAN Pages: 9

Brand: ForeScout Pages: 28

Brand: Black Box Pages: 37

Brand: Seattle Computer Products Pages: 31

Enterasys Matrix 2G4082-25

Brand: Enterasys Pages: 58

Brand: Patton Pages: 62

IP-Logic ZIG-IPPRO-RX

Brand: Zigen Pages: 4

airMAX NanoBridge M NBM3

Brand: Ubiquiti Pages: 24

SmartRack SR25UBEXP

Brand: Tripp Lite Pages: 4

Brand: Hama Pages: 24

Brand: Meinberg Pages: 14

Brand: Wave wifi Pages: 3

Brand: FiberHome Pages: 44

Quark SoC X1000

Brand: Galileo Pages: 20

NetStructure ZT 5085

Brand: Intel Pages: 106

Brand: Alcatel Pages: 158

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands