Huawei SmartAX MA5616 Configuration Manual Download | Manualshive

Page: 398 / 553

background image

–

Generally, the priorities are in a descending order for the VoIP service, IPTV
service, and Internet service. In this example, set the traffic profile index to 7 and
the 802.1p priority of the Internet service to 1.

huawei(config)#

traffic table ip index 7 cir 1024 priority 1 priority-

policy loca
l-Setting

3.

Add service ports to the VLAN.

Add service ports to the VLAN and use the traffic profile configured in the preceding
step.

huawei(config)#

service-port vlan 102 vdsl mode atm 0/1/0 vpi 0 vci 35

multi-serv
ice user-8021p 2 rx-cttr 7 tx-cttr 7

huawei(config)#

service-port vlan 102 vdsl mode atm 0/1/1 vpi 0 vci 35

multi-serv
ice user-8021p 2 rx-cttr 7 tx-cttr 7

4.

Save the data.

huawei(config)#

save

l

Configure the VoIP service.
1.

Create a VLAN and add the uplink port to the VLAN.

huawei(config)#

vlan 103 smart

huawei(config)#

port vlan 103 0/0 1

2.

Configure a traffic profile.

Set the traffic profile index to 8 and the 802.1p priority of the VoIP service to 6.

huawei(config)#

traffic table ip index 8 cir 64 priority 6 priority-policy

local-
Setting

3.

Add service ports to the VLAN.

Add service ports to the VLAN and use the traffic profile configured in the preceding
step.

huawei(config)#

service-port vlan 103 vdsl mode atm 0/1/0 vpi 0 vci 35

multi-serv
ice user-8021p 3 rx-cttr 8 tx-cttr 8

huawei(config)#

service-port vlan 103 vdsl mode atm 0/1/1 vpi 0 vci 35

multi-serv
ice user-8021p 3 rx-cttr 8 tx-cttr 8

4.

Save the data.

huawei(config)#

save

l

Configure the IPTV service.
1.

Create a VLAN and add the uplink port to the VLAN.

huawei(config)#

vlan 104-105

smart

It will take several minutes, and console may be timeout, please use
command
idle-timeout to set time
limit
Are you sure to add VLANs? (y/n)
[n]:

y

The total of the VLANs having been processed is
2
The total of the added VLANs is 2
huawei(config)#

port vlan 104-105 0/0

1

It will take several minutes, and console may be timeout, please use
command

SmartAX MA5616 Multi-service Access Module
Configuration Guide

8 Configuration Example of Services on the MA5616

Through GPON Upstream Transmission

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

387

«
...
396
397
398
399
400
...
»

Summary of Contents for SmartAX MA5616










































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SmartAX MA5616

Brand: Lab.gruppen Pages: 35

Brand: PaloAlto Networks Pages: 3

Brand: Ubiquiti Pages: 23

Asynchronous SH7145F

Brand: Renesas Pages: 17

ADSL/ADSL2/ADSL2+ Router 660R-6xC Series

Brand: ZyXEL Communications Pages: 282

Millennium P650

Brand: Matrox Pages: 54

Brand: TP-Link Pages: 7

Brand: TP-Link Pages: 2

Brand: CyberTAN Pages: 67

Brand: Kramer Pages: 2

Brand: Rainbow Pages: 2

EtherLink 3C905C-TX

Brand: 3Com Pages: 96

Brand: Intercoax Pages: 2

Brand: Rolls Pages: 1

Brand: Amit Pages: 75

Brand: EMC Pages: 88

Brand: ZyXEL Communications Pages: 191

Brand: Behringer Pages: 15

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands