Huawei SmartAX MA5616 Configuration Manual Download | Manualshive

Page: 42 / 553

background image

Figure 3-22

Flowchart for configuring the NMS

Set the SNMP parameters

Set the source address for

traps sending

Save the data

Set the IP address of the

target host for traps

Start

End

Enable trap sending

Flowchart for

configuring the MXU

Procedure

l

Configuration procedure on the device
1.

Configure the SNMP parameters.

a.

Configure the community names and the access rights.
Run the

snmp-agent community

command to configure the community names

and the access rights.

NOTE

The read community name is

public

. The write community name is

private

.

The read community name and the write community name on the device must be the
same as those configured on the U2000.

huawei(config)#

snmp-agent community read public

huawei(config)#

snmp-agent community write private

b.

(Optional) Set the information about the administrator.
Run the

snmp-agent sys-info

command to set the contact of the SNMP Agent

administrator and the physical position of the device.
Contact of the administrator: HW-075528780808. Physical position of the
device: Shenzhen_China.

huawei(config)#

snmp-agent sys-info contact HW-075528780808

huawei(config)#

snmp-agent sys-info location Shenzhen_China

c.

Set the SNMP version.
Run the

snmp-agent sys-info

command to set the required SNMP version.

huawei(config)#

snmp-agent sys-info version v1

NOTE

The SNMP version on the device must be the same as that configured on the U2000.

SmartAX MA5616 Multi-service Access Module
Configuration Guide

3 Basic Configuration

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

31

«
...
40
41
42
43
44
...
»

Summary of Contents for SmartAX MA5616










































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SmartAX MA5616

Brand: D-Link Pages: 267

Brand: Farallon Pages: 26

Brand: Observint Pages: 11

Brand: Ubiquiti Pages: 50

Brand: TFortis Pages: 86

ZyXEL EES-1024AF

Brand: ZyXEL Communications Pages: 99

Brand: Keithley Pages: 98

Duinotech Lilypad Plus XC3920

Brand: Jaycar Electronics Pages: 2

UM10301 PCA8565

Brand: NXP Semiconductors Pages: 54

SmartSTACK ELS100-24TXM

Brand: Cabletron Systems Pages: 117

Broadband 700 MHz

Brand: Alcatel-Lucent Pages: 8

Brand: Comtrend Corporation Pages: 208

Brand: Dynamix Pages: 87

Brand: ActionTec Pages: 87

Brand: ZALMAN Pages: 8

Brand: IBM Pages: 44

Brand: Ezquest Pages: 65

Brand: Arctic Pages: 7

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands