Huawei SmartAX MA5616 Configuration Manual Download | Manualshive

Page: 360 / 553

background image

huawei(config-mvlan4003)#

igmp mode proxy

Are you sure to change IGMP mode?(y/n)[n]:

y

Step 4

Configure the multicast uplink port.

huawei(config-mvlan4003)#

igmp uplink-port 0/0/1

huawei(config-mvlan4003)#

multicast-vlan 4002

huawei(config-mvlan4002)#

igmp uplink-port 0/0/1

Step 5

Configure multicast programs.

Configure the program in the multicast VLAN in dynamic generation mode, and specify the IP
address range of the program that can be requested by the user to 224.1.1.1-224.1.1.2.

NOTE

The execution of the

igmp match mode

command for configuring the mode of the multicast program will cause

the user to go offline. Therefore, plan the multicast program mode before configuring the multicast program.
This command can be executed only when the IGMP function is disabled.

huawei(config-mvlan4002)#

igmp match group ip 224.1.1.1 to-ip 224.1.1.2

huawei(config-mvlan4002)#

multicast-vlan 4003

huawei(config-mvlan4003)#

igmp match group ip 224.1.1.1 to-ip 224.1.1.2

Step 6

Configure multicast users.

huawei(config-mvlan4002)#

btv

huawei(config-btv)#

igmp user add service-port 100

huawei(config-btv)#

igmp user add service-port 101

huawei(config-btv)#

multicast-vlan 4002

huawei(config-mvlan4002)#

igmp multicast-vlan member service-port 100

huawei(config-mvlan4002)#

multicast-vlan 4003

huawei(config-mvlan4003)#

igmp multicast-vlan member service-port 101

huawei(config-mvlan4003)#

quit

Step 7

Save the data.

huawei(config)#

save

----End

Result

l

User 1 belongs to multicast VLAN 4002 and user 1 can watch the program with IP address
224.1.1.1 provided by ISP1.

l

User 2 belongs to multicast VLAN 4003 and user 2 can watch the program with IP address
224.1.1.2 provided by ISP2.

Configuration File

The following part describes the configuration file of this configuration example. Note that
certain steps need to be performed manually and the configuration file cannot be imported
directly.

Create VLANs and add an uplink port to the VLANs. This step needs to be performed manually.

vlan 4002 to 4005 smart
port vlan 4002 to 4005 0/0 1

Create service ports.

service-port 100 vlan 4004 vdsl mode ptm 0/1/0 multi-service user-vlan untagged rx-
cttr 6 tx-cttr 6
service-port 101 vlan 4005 vdsl mode ptm 0/1/1 multi-service user-vlan untagged rx-
cttr 6 tx-cttr 6

Configure multicast VLANs and the IGMP mode. This step needs to be performed manually.

SmartAX MA5616 Multi-service Access Module
Configuration Guide

8 Configuration Example of Services on the MA5616

Through GPON Upstream Transmission

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

349

«
...
358
359
360
361
362
...
»

Summary of Contents for SmartAX MA5616










































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SmartAX MA5616

Brand: 3Com Pages: 20

Brand: H3C Pages: 6

OfficeConnect 3CP4144

Brand: 3Com Pages: 4

OfficeConnect 3CP4144

Brand: 3Com Pages: 2

Brand: H3C Pages: 60

Brand: H3C Pages: 149

Brand: 3Com Pages: 27

Brand: Data Translation Pages: 98

Brand: Nayar Systems Pages: 37

Brand: Ubiquiti Pages: 23

Brand: Draytek Pages: 8

eXtremeRAID 1100

Brand: Mylex Pages: 74

Brand: E-Lins Pages: 113

Speed Touch 591s

Brand: Alcatel Pages: 184

Brand: Idis Pages: 85

Brand: Supero Pages: 16

PSoC 4 S Series

Brand: Cypress Pages: 4

Brand: ZyXEL Communications Pages: 79

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands