manualshive.com logo in svg

Huawei SmartAX MA5616, Configuration Manual

The Huawei SmartAX MA5616 Configuration Manual is a detailed and comprehensive guide that enables users to efficiently set up and optimize their Huawei SmartAX MA5616. Easily downloadable for free from manualshive.com, this manual provides step-by-step instructions and essential information to maximize your product experience.

Share
Download
background image

l

Run the 

display if-h248 state

 command to check whether the MG interface is in the normal

state.

l

Run the 

quit

 command to quit the global config mode, and then run the 

display if-h248

all

 command to check whether the MG interface is in the normal state.

----End

Example

To enable H.248-based MG interface 0, do as follows:

huawei(config)#

interface h248 0

huawei(config-if-h248-0)#

reset coldstart

  Are you sure to reset MG interface?(y/n)[n]:

y

huawei(config-if-h248-0)#

quit

huawei(config)#

display if-h248 all

                                              

--------------------------------------------------------------------------------
MGID     TransMode State          MGPort MGIP           MGCPort MGCIP/DomainName
--------------------------------------------------------------------------------
0        UDP       Normal         2944   10.10.10.11     2944   10.10.20.11     
--------------------------------------------------------------------------------

7.3.2 Configuring the IUA Link

This topic describes how to configure the IUA link for signaling transmission between the
MA5616 and MGC in the VoIP ISDN BRA service.

Context

l

Simple Control Transmission Protocol (SCTP) is a connection-oriented protocol. Its most
fundamental function is to provide reliable transmission for interaction messages between
the MA5616 and MGC. The SCTP protocol implements services based on the association
between two SCTP endpoints. SCTP can be regarded as a transmission layer. Its upper
layer is called SCTP subscriber, and its lower layer is the IP network.

l

The IUA link is the carrier of the interaction signaling between the MA5616 and MGC.

7.3.2.1 Adding an IUA Link Set

This topic describes how to add an IUA link set. When configuring the VoIP ISDN service, you
need to configure the IUA link to carry the Q.931 call signaling. Before adding an IUA link, you
must add a corresponding link set. Otherwise, the link cannot be added.

Context

l

The system supports the configuration of a maximum of two IUA link sets.

l

After a link set is configured successfully, the system is in the deactivated state by default.

Procedure

Step 1

In global config mode, run the 

sigtran

 command to enter the Sigtran mode.

Step 2

Run the 

iua-linkset add

 command to add an IUA link set.

Step 3

You can run the 

display iua-linkset attribute

 command to check whether the configured IUA

link set information is the same as the data plan.

----End

SmartAX MA5616 Multi-service Access Module
Configuration Guide

7 Configuring the Voice Service

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

289

Summary of Contents for SmartAX MA5616










































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SmartAX MA5616

D-Link DES-7200 User Manual preview
DES-7200
Brand: D-Link Pages: 100
D-Link DES-3226L Manual preview
DES-3226L
Brand: D-Link Pages: 134
D-Link DES-3010F Command Line Interface Manual preview
DES-3010F
Brand: D-Link Pages: 187
D-Link DES-3010F Manual preview
DES-3010F
Brand: D-Link Pages: 225
D-Link DES-1048G Manual preview
DES-1048G
Brand: D-Link Pages: 31
D-Link DES-1050G User Manual preview
DES-1050G
Brand: D-Link Pages: 35
D-Link DES-1016D - Switch Quick Install Manual preview
DES-1016D - Switch
Brand: D-Link Pages: 19
D-Link COVR-2202 User Manual preview
COVR-2202
Brand: D-Link Pages: 107
D-Link AirPlusXtremeG DI-624 Troubleshooting preview
AirPlusXtremeG DI-624
Brand: D-Link Pages: 5
D-Link DGS-1210-28P Getting Started Manual preview
DGS-1210-28P
Brand: D-Link Pages: 48
Aastra CNX Product Brief preview
CNX
Brand: Aastra Pages: 2
Cabletron Systems Netlink FRX8000 Installation And Setup Manual preview
Netlink FRX8000
Brand: Cabletron Systems Pages: 94
Cabletron Systems MMAC-Plus 9E423-24 Reference Manual preview
MMAC-Plus 9E423-24
Brand: Cabletron Systems Pages: 10
Cabletron Systems MMAC-Plus 9A128-01 Management Manual preview
MMAC-Plus 9A128-01
Brand: Cabletron Systems Pages: 22
Cabletron Systems Spectrum EMM-E6 Addendum Manual preview
Spectrum EMM-E6
Brand: Cabletron Systems Pages: 2
Cabletron Systems SmartSTACK ELS100-24TXG Installation And User Manual preview
SmartSTACK ELS100-24TXG
Brand: Cabletron Systems Pages: 112
Cabletron Systems ESX-1380 Management Manual preview
ESX-1380
Brand: Cabletron Systems Pages: 86
Cabletron Systems DLM6C-AA Overview And Setup Manual preview
DLM6C-AA
Brand: Cabletron Systems Pages: 54

Brands by name

Popular brands

Load more brands