Huawei SmartAX MA5616 Configuration Manual Download | Manualshive

Page: 198 / 553

background image

Example

Assume that multicast user (port) 0/1/0 (with an index of the user traffic stream 100) is added
to multicast VLAN 10, the user authentication and the log report function are enabled, the
maximum number of programs that can be concurrently watched is 4, and rights profile

music

is bound to the user. To perform the configurations, do as follows:

huawei(config)#

btv

huawei(config-btv)#

igmp user add service-port 100 auth log enable max-program 4

huawei(config-btv)#

igmp user bind-profile service-port 100 profile-name music

huawei(config-btv)#

quit

huawei(config)#

multicast-vlan 10

huawei(config-mvlan10)#

igmp multicast-vlan member service-port 100

Result

Check whether the multicast user is configured correctly.

huawei(config)#

display igmp user 0

//

0 is the index of the multicast user. You can

run the display igmp user all command to query the index of the multicast user.

{ <cr>||<K> }:

Command:
display igmp user 0
User : 0/1/0 //

Port of the multicast user

State : offline
Authentication : auth //

Authentication is

required.

Quick leave : MAC-based
IGMP flow ID : 100
Video flow ID : 100
Log switch : enable
Bind profiles : 1
IGMP version : IGMP v3
Available programs : 4 //

The maximum number of programs that

can be concurrently watched is 4.

Global Leave : disable
User MaxBandWidth : no-limit
Used bandwidth(kbps) : 0
Used bandwidth
to max bandwidth(%) : -
Total video bandwidth : -
Mcast video bandwidth : -
Bind profile list
---------------------------------------------
index Profile name Program number
---------------------------------------------
0 music 0 //

The bound rights profile is

music.

---------------------------------------------
Total: 1

6.2.4 (Optional) Configuring the Multicast Bandwidth

To limit the multicast bandwidth of a user, you can enable the multicast bandwidth management
function, namely, connection admission control (CAC), and then control the bandwidth of the
multicast user by setting the program bandwidth and the user bandwidth.

Prerequisites

The program matching mode of the multicast VLAN must be the static configuration mode.

Context

If the CAC function, not the dynamic Access Node Control Protocol (ANCP) CAC function is
enabled, and a user requests for a multicast program, the system compares the remaining

SmartAX MA5616 Multi-service Access Module
Configuration Guide

6 Configuring the Multicast Service (Multicast VLAN Mode)

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

187

«
...
196
197
198
199
200
...
»

Summary of Contents for SmartAX MA5616










































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SmartAX MA5616

RDX QuikStation 4

Brand: Tandberg Data Pages: 2

Brand: Ubiquiti Pages: 50

Brand: Vivotek Pages: 136

Brand: Opvimus Pages: 12

Brand: Falcon Pages: 24

Brand: iBall Baton Pages: 9

RUGGEDMAX WIN7000

Brand: RuggedCom Pages: 42

PCI-6110E/6111E

Brand: National Instruments Pages: 113

TE100-S16 - 10/100Mbps Ethernet Switch

Brand: TRENDnet Pages: 15

EZ-Extender Analog 120-Pin Probing Board

Brand: Analog Devices Pages: 29

Seven Solutions WR-ZEN Series

Brand: Orolia Pages: 167

Brand: Aaeon Pages: 61

Brand: Gigabyte Pages: 18

IPLink 2603 Series

Brand: Patton Pages: 120

Brand: DigiTech Pages: 6

Brand: Omron Pages: 432

Brand: Neousys Technology Pages: 24

Brand: ADS Technologies Pages: 1

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands