Huawei SmartAX MA5616 Configuration Manual Download | Manualshive

Page: 133 / 553

background image

Context

Traffic suppression can be configured based on the port of a board.

Procedure

Step 1

Run the

interface eth

command to enter the ETH mode.

Step 2

Query the thresholds of traffic suppression.
Run the

display traffic-suppress all

command to check whether the thresholds of traffic

suppression meets the service requirements.

Step 3

Run the

traffic-suppress

command to suppress the traffic of the port.

The main parameters are as follows:

l

broadcast

: Suppresses the broadcast traffic.

l

multicast

: Suppresses the unknown multicast traffic.

l

unicast

: Suppresses the unknown unicast traffic.

l

value

: Indicates the index of the traffic suppression level. The index value is the value queried

in step 2.

----End

Example

To suppress the broadcast packets according to traffic suppression level 8 on port 0 on the ETH
board in slot 0/3, do as follows:

huawei(config)#

interface eth 0/3

huawei(config-if-eth-0/3)#

display traffic-suppress all

Command:
display traffic-suppress all
Traffic suppression ID definition:
---------------------------------------------------------------------
NO. Min bandwidth(kbps) Max bandwidth(kbps) Package number(pps)
---------------------------------------------------------------------
1 6 145 12
2 12 291 24
3 24 582 48
4 48 1153 95
5 97 2319 191
6 195 4639 382
7 390 9265 763
8 781 18531 1526
9 1562 37063 3052
10 3125 74126 6104
11 6249 148241 12207
12 12499 296483 24414
13 0 0 0
---------------------------------------------------------------------
---------------------------------------------------------------------
PortID Broadcast_index Multicast_index Unicast_index
---------------------------------------------------------------------
0 7 7 7
1 7 7 7
2 7 7 7
3 7 7 7
4 7 7 7
5 7 7 7
6 7 7 7
7 7 7 7

SmartAX MA5616 Multi-service Access Module
Configuration Guide

3 Basic Configuration

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

122

«
...
131
132
133
134
135
...
»

Summary of Contents for SmartAX MA5616










































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SmartAX MA5616

Brand: D-Link Pages: 11

Brand: D-Link Pages: 83

Brand: D-Link Pages: 129

Brand: D-Link Pages: 10

Brand: D-Link Pages: 21

Brand: D-Link Pages: 6

Brand: D-Link Pages: 17

Brand: D-Link Pages: 4

Brand: D-Link Pages: 6

Brand: D-Link Pages: 86

Brand: D-Link Pages: 3

Brand: D-Link Pages: 4

Brand: D-Link Pages: 4

DSL-3580L Series

Brand: D-Link Pages: 20

Brand: D-Link Pages: 64

Brand: D-Link Pages: 73

Brand: Lauterbach Pages: 61

Brand: Campbell Pages: 42

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands