Huawei SmartAX MA5616 Configuration Manual Download | Manualshive

Page: 504 / 553

background image

Figure 10-2

Example network of the multiple service in FTTB and FTTC service

10.4.1 Configuring the FTTB and FTTC Internet Access Services
(ADSL2+ Access)

The OLT is connected to a remote ONU that supports ADSL2+ access by using the GPON port
to provide users with the high-speed Internet access service.

Service Requirements

l

VLANs are divided are isolated different user groups, preventing broadcast storms and
facilitating O&M.

l

Users perform PPPoE dialup on PCs to implement high-speed Internet access.

l

Two VLAN tags are used to precisely identify services and users.

l

The same QoS is used for the same type of services on the same type of ONUs, facilitating
management.

Prerequisite

l

The example network as shown in

Figure 10-2

is complete.

l

Corresponding ONU version: V800R309C00. If another version is used, the configuration
differs slightly. For details, see the configuration guide of the corresponding ONU version.

l

The ADSL mode of ONU is NGADSL (namely RFC4706).

NOTE

You can run the

display xdsl mode

command in the privilege mode to query the ADSL mode.

Background Information

ONUs that support ADSL2+ access include MA5616.

Procedure

l

Configure the OLT.

SmartAX MA5616 Multi-service Access Module
Configuration Guide

10 Configuration Examples of the FTTx

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

493

«
...
502
503
504
505
506
...
»

Summary of Contents for SmartAX MA5616










































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SmartAX MA5616

Brand: GE Pages: 146

Brand: Xantrex Pages: 8

RDX QuikStation 4

Brand: Tandberg Data Pages: 2

Brand: Zhone Pages: 7

Brand: Zhone Pages: 1

Brand: REXROTH Pages: 68

Brand: RadiSys Pages: 44

Brand: Lindy Pages: 4

TOWERCHRON DP72

Brand: Grasslin Pages: 2

Brand: Cypress Semiconductor Pages: 10

Barricade SMC7901WBRA2

Brand: SMC Networks Pages: 2

Brand: Asante Pages: 150

Brand: Giacomini Pages: 2

Brand: Z3 Technology Pages: 67

BLKDP45SG - MB 1333FSB DDR3 1333 Aud+Lan RAID SATA ATX

Brand: Intel Pages: 86

Brand: XtendLan Pages: 52

Brand: ADIC Pages: 140

Brand: Digisol Pages: 81

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands