Huawei SmartAX MA5616 Configuration Manual Download

Page: 69 / 553

Prerequisites

Run the switch adsl mode to rfc4706 command to switch to the ADSL mode NGADSL.

Context

The MA5616 supports two ADSL modes, that is, ADSL mode and NGADSL mode. The two
modes can be switched by running a command.

In this document, the configuration specified is based on the NGADSL mode. By default, the
system supports the ADSL mode.

When activating an ADSL2+ port, you need to bind the ADSL2+ line template and alarm
template to the port.

An ADSL2+ line template should be formed by binding an ADSL2+ line profile with an
ADSL2+ channel profile.

An ADSL2+ line alarm template should be formed by binding an ADSL2+ line alarm
profile with an ADSL2+ channel alarm profile.

Figure 3-23

shows the flow for configuring an ADSL2+ template.

Figure 3-23

Flowchart for configuring an ADSL2+ template

Configure an

ADSL2+ channel profile

Configure an

ADSL2+ line profile

Start

Configure an

ADSL+ line template

End

Configure an ADSL2+

channel alarm profile

Configure an

ADSL2+ line alarm profile

Start

Configure an

ADSL2+ alarm template

End

Flowchart for configuring a

line template

Flowchart for configuring an

alarm template

Procedure

Configure an ADSL2+ line template.

Run the

adsl line-profile quickadd

command to quickly add an ADSL2+ line profile,

or run the interactive

adsl line-profile add

command to add an ADSL2+ line profile.

Main parameters:

–

transmode

and

Transmission mode

(in interactive mode): Indicates the line

transmission mode. By default, the system supports all transmission modes. The
user can adopt the default value for auto-adaptation.

SmartAX MA5616 Multi-service Access Module
Configuration Guide

3 Basic Configuration

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

Summary of Contents for SmartAX MA5616










































































































































































































































































































































































































































































































































































Search results

Summary of Contents for SmartAX MA5616

Reviews:

Related manuals for SmartAX MA5616

Brands by name

Popular brands

Huawei SmartAX MA5616, Configuration Manual

Search results

Summary of Contents for SmartAX MA5616

Reviews:

Related manuals for SmartAX MA5616

Brands by name

Popular brands