Huawei SmartAX MA5616 Configuration Manual Download | Manualshive

Page: 431 / 553

background image

Prerequisite

The number of xDSL ports is under the control of licenses. Make sure that sufficient licenses
are already requested.

Procedure

Step 1

Create a VLAN.

Create smart VLAN 50.

huawei(config)#

vlan 50 smart

Step 2

Configure upstream ports.
Add upstream ports 0/0/1 and 0/0/0 to VLAN 50. Two ports are added for the purpose of port
aggregation.

huawei(config)#

port vlan 50 0/0 0

huawei(config)#

port vlan 50 0/0 1

To aggregate the two upstream ports as one aggregation group, set the packet forwarding mode
of the aggregation group to egress-ingress, and set the aggregation group to work in the LACP
static mode, do as follows:

huawei(config)#

link-aggregation 0/0 0 0/0 1 egress-ingress workmode lacp-static

NOTE

The aggregated ports must meet the following requirements: The ports must work in the full-duplex mode; the
port rates must be the same and the rate of an electrical port must not be of the auto-negotiation type; the attributes
of the ports, such as the default VLAN ID (PVID) and VLAN, must be the same; one port can belong to only
one aggregation group; the port must not be a mirroring destination port; the port must not be in the auto-
negotiation mode; the start port ID must be smaller than the end port ID.

Step 3

In the case of the ADSL access mode, follow this procedure.
1.

Configure an ADSL2+ profile. For details, see

3.7.1 Configuring the ADSL2+ Profile

.

The ID of the ADSL2+ line profile is 3, the downstream rate is 2048 kbit/s, the channel
mode is the interleave mode, the maximum interleave delay is 10 ms, and the SNR margin
is 6 dB.

huawei(config)#

adsl line-profile quickadd 3 snr 60 30 120 60 30 120

huawei(config)#

adsl channel-profile quickadd 3 interleaved-delay 10 10 rate

1024
2048 3096 1024 2048
3096

huawei(config)#

adsl line-template quickadd 3 line 3 channel1 3 60 70 channel2

3

2.

Activate the ADSL port. The port is port 0/2/0, and ADSL line template 3 and the default
alarm template (alarm template 1) are bound to the port.

NOTE

By default, an ADSL port is in the activated state. Before binding a template to the port, you must deactivate
the port.

huawei(config)#

interface adsl 0/2

huawei(config-if-adsl-0/2)#

deactivate 0

huawei(config-if-adsl-0/2)#

activate 0 template-index 3

huawei(config-if-adsl-0/2)#

alarm-config 0 1

huawei(config-if-adsl-0/2)#

quit

3.

Run the

display traffic table ip

command to query the traffic profiles that exist in the

system.

huawei(config)#

display traffic table ip from-index

0

{ <cr>|to-

SmartAX MA5616 Multi-service Access Module
Configuration Guide

9 Configuration Example of Services on the MA5616

Through GE Upstream Transmission

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

420

«
...
429
430
431
432
433
...
»

Summary of Contents for SmartAX MA5616










































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SmartAX MA5616

Brand: PaloAlto Networks Pages: 2

Brand: Alesis Pages: 61

Scorpio WD2500BPVT

Brand: Western Digital Pages: 3

Scorpio WD2500BPVT

Brand: Western Digital Pages: 4

Brand: N.A.T. Pages: 32

Brand: JETWAY Pages: 55

Brand: Tbus Pages: 25

Brand: Faderfox Pages: 10

Brand: Renesas Pages: 20

Brand: Zalip Pages: 77

EtherFast LNE100TX ver. 5

Brand: Linksys Pages: 42

Brand: UTStarcom Pages: 71

Brand: Dataprobe Pages: 5

SinoCon C2000-C2-SHK0401-BB1

Brand: KonNad Pages: 12

RanaSystems 13-0010--001

Brand: RANA Systems Pages: 328

Brand: SYNTEK Pages: 41

Brand: Solwise Pages: 7

Brand: Magma Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands