manualshive.com logo in svg

Huawei SmartAX MA5616, Configuration Manual

The Huawei SmartAX MA5616 Configuration Manual is a detailed and comprehensive guide that enables users to efficiently set up and optimize their Huawei SmartAX MA5616. Easily downloadable for free from manualshive.com, this manual provides step-by-step instructions and essential information to maximize your product experience.

Share
Download
background image

huawei(config)#

interface sip 0

huawei(config-if-sip-0)#

fax-modem parameters negomode self-switch vbd-codec g.711a 

vbd-pt-type
 static rtp-interval 1

huawei(config-if-sip-0)#

rfc2198 set rfc2198-negomode fixedstart rfc2198-startmode 

smart2198

huawei(config-if-sip-0)#

modem parameters transmode 0

huawei(config-if-sip-0)#

display fax-modem parameters

 -------------------------------------------------------------------------------
 MGID                   :0
 Nego-mode              :self-switch
 Rtp-interval           :10ms
 Vbd-codec              :G.711A
 Vbd-pt-type            :static
 Vbd-attribute-type     :v.152
 -------------------------------------------------------------------------------

huawei(config-if-sip-0)#

display modem parameters

 ---------------------------------------
 MGID      Transmode
 ---------------------------------------
 0         Thoroughly
 ---------------------------------------

7.8 Configuring the Security and Reliability of the Voice
Service

For the MA5616, the security configuration of the voice service includes the H.248-based, or
SIP-based device authentication configuration. The reliability configuration of the voice service
includes the dual-homing configuration and the emergency standalone configuration.

7.8.1 Configuring the Device Authentication

The purpose of authentication is to verify the validity of users and networks. The same
authentication algorithm is used on the MG and the MGC separately. Then, the calculation results
on the MG and the MGC are compared on either side. If the calculation results are the same, it
indicates that the authentication is successful. If the calculation results are different, it indicates
that the authentication fails.

7.8.1.1 Configuring the Device Authentication (Based on the H.248 Protocol)

This topic describes how to configure the device authentication parameters of the MA5616 to
prevent illegal devices from registering with the MGC when the H.248 protocol is used.

Prerequisites

l

The MG interface must be added successfully on the MA5616.

l

The parameters, including the encryption type, the initial key, and the DH authentication
MG ID, must be configured on the MGC. These parameters must be the same as the
parameters configured on the MA5616.

Precautions

When the MGC is Huawei SoftX3000, the authentication MG ID must be a string of more than
eight characters.

SmartAX MA5616 Multi-service Access Module
Configuration Guide

7 Configuring the Voice Service

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

306

Summary of Contents for SmartAX MA5616










































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SmartAX MA5616

Samsung AllShare Cast Dongle Quick Start Manual preview
AllShare Cast Dongle
Brand: Samsung Pages: 2
D-Link DSL-2750U Setup preview
DSL-2750U
Brand: D-Link Pages: 14
D-Link DVG-7022S Quick Installation Manual preview
DVG-7022S
Brand: D-Link Pages: 7
D-Link DIR-878 Quick Installation Manual preview
DIR-878
Brand: D-Link Pages: 41
PACOM Professional Series Quick Manual preview
Professional Series
Brand: PACOM Pages: 15
D-Link DSL-500 Quick Start Manual preview
DSL-500
Brand: D-Link Pages: 11
D-Link DHP?P309AV Setup Manual preview
DHP?P309AV
Brand: D-Link Pages: 8
D-Link AirPlus DWL-810 Quick Installation Manual preview
AirPlus DWL-810
Brand: D-Link Pages: 8
D-Link DFE-690TXD Quick Install Manual preview
DFE-690TXD
Brand: D-Link Pages: 12
D-Link DHP-601AV Quick Installation Manual preview
DHP-601AV
Brand: D-Link Pages: 84
VAF instruments 667 Instructions For Installation, Operation And Maintenance preview
667
Brand: VAF instruments Pages: 56
Commell LS-570 User Manual preview
LS-570
Brand: Commell Pages: 58
DCE ANS-205 User Manual preview
ANS-205
Brand: DCE Pages: 5
ekwb EK-FC Installation Manual preview
EK-FC
Brand: ekwb Pages: 2
Idis DR-8400 Installation Manual preview
DR-8400
Brand: Idis Pages: 31
Compaq StorageWorks AIT 35GB AutoLoader Overview And Installation preview
StorageWorks AIT 35GB AutoLoader
Brand: Compaq Pages: 4
IEI Technology HPE-6S2 Quick Installation Manual preview
HPE-6S2
Brand: IEI Technology Pages: 3
Eneo PNR-5304 Quick Installation Manual preview
PNR-5304
Brand: Eneo Pages: 68

Brands by name

Popular brands

Load more brands