Huawei SmartAX MA5616 Configuration Manual Download | Manualshive

Page: 277 / 553

background image

Item

Remarks

Coding mode
of the MG
interface

Currently, only the

text

mode is

supported.

Transmission
mode of the
MG interface

The transmission mode is
selected according to the
requirements of the MGC.
Generally, UDP is used.

Domain name
of the MG
interface

It corresponds to the

domainName

parameter of the

MG interface.
When the H.248 protocol is used,
this parameter must be
configured if the

MIDType

parameter of the H.248 message
is configured to

domainName

.

Otherwise, the MG interface
cannot be started. In other
situations, this parameter is
optional.

Device name
of the MG
interface

It is supported by only the H.248
protocol, and it corresponds to the

deviceName

parameter of the

MG interface that uses the H.248
protocol.
This parameter must be
configured if the

MIDType

parameter of the H.248 message
is configured to

domainName

.

Otherwise, the MG interface
cannot be started. In other
situations, this parameter is
optional.

Digitmap of the MG interface

The digitmaps are used for certain
special applications such as
emergency calls and emergency
standalone. The digitmaps for
common phone services are
issued to the AG by the MGC, and
therefore such digitmaps need not
be configured on the AG. If the
services such as emergency calls
and emergency standalone are
not required, this parameter need
not be configured.

SmartAX MA5616 Multi-service Access Module
Configuration Guide

7 Configuring the Voice Service

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

266

«
...
275
276
277
278
279
...
»

Summary of Contents for SmartAX MA5616










































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SmartAX MA5616

Brand: Hal Communications Pages: 25

TokenLink 3C359B

Brand: 3Com Pages: 4

TokenLink 3C359B

Brand: 3Com Pages: 8

TokenLink 3C339

Brand: 3Com Pages: 2

EtherLink 3C985B-SX

Brand: 3Com Pages: 44

Brand: 3Com Pages: 88

Brand: 3Com Pages: 2

Brand: 3Com Pages: 111

TokenLink 3C359

Brand: 3Com Pages: 4

Brand: 3Com Pages: 74

Brand: 3Com Pages: 6

Brand: Aastra Pages: 2

Brand: Zonet Pages: 10

Brand: Samsung Pages: 65

Brand: Oracle Pages: 112

Brand: Teknim Pages: 10

AT-8550/SP Series

Brand: Allied Telesis Pages: 114

Brand: Belkin Pages: 57

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands