Huawei SmartAX MA5616 Configuration Manual Download

Page: 5 / 553

3.3.1 Configuring an Uplink Ethernet Port

3.15.1.2 Configuring the Monitoring Through the ESCM

3.15.2.1 Configuring the Monitoring Through the EPS30-4815AF

3.15.3 Configuring the Monitoring Through the Fan

Updates in Issue 03 (2011-03-31)

Compared with issue 02 (2011-03-05) of V800R308C01, 03 (2011-03-31) has the following
changes:

The following information is modified:

2 Checking Before the Configuration

Updates in Issue 02 (2011-03-05)

Compared with issue 01 (2011-01-07) of V800R308C01, 02 (2011-03-05) has the following
changes:

The following information is modified:

3.6 Configuring a VLAN

3.8.1.1 Configuring the Adaptive Clock Reference Source

3.11.3 Preventing the Attack of Invalid Users

4 Configuring the Ethernet CFM OAM

5.3 Configuring an xDSL Port

6.2.2 Configuring the Multicast Program

8.1.4 Configuration Example of the xDSL IPoA Internet Access Service

Issue 01 (2011-01-07)

Compared with issue 02 (2010-07-25) of V800R307C01, V800R308C01 has the following
changes:

Added:

3.7.3.2 Configuring the VDSL2 Profile (TI Mode)

3.8 Configuring the System Clock

3.9 Configuring the System Time

3.10 Configuring the User Security

3.12 Configuring AAA

3.13 Configuring the ACL for Packet Filtering

5 Configuring the xDSL Internet Access Service

9 Configuration Example of Services on the MA5616 Through GE Upstream
Transmission

SmartAX MA5616 Multi-service Access Module
Configuration Guide

About This Document

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

Summary of Contents for SmartAX MA5616










































































































































































































































































































































































































































































































































































Search results

Summary of Contents for SmartAX MA5616

Reviews:

Related manuals for SmartAX MA5616

Brands by name

Popular brands

Huawei SmartAX MA5616, Configuration Manual

Search results

Summary of Contents for SmartAX MA5616

Reviews:

Related manuals for SmartAX MA5616

Brands by name

Popular brands