Huawei SmartAX MA5616 Configuration Manual Download | Manualshive

Page: 164 / 553

background image

4

Configuring the Ethernet CFM OAM

On the Ethernet network, Ethernet connectivity fault management (CFM) OAM is defined as
connectivity fault management in IEEE 802.1ag to implement the OAM function of connectivity
detection on the Ethernet bearer network. Ethernet CFM OAM is applicable to the end-to-end
(E2E) network with a large scale and it is the network-level OAM.

Prerequisites

l

Network devices and lines must be in the normal state.

l

The OLT must support the Ethernet CFM OAM function.

Context

OAM is a key method of reducing network maintenance cost.

Ethernet is a widely used local area network (LAN) technology. It provides rich bandwidth,
features low cost, and supports plug-and-play and multipoint operations. As the Ethernet
technology is developing from carriers' networks to metropolitan area networks (MANs) and
wide area networks (WANs), the network management and maintenance are increasingly
important. Currently, however, Ethernet does not support carrier-class management, and thus
L2 network faults cannot be detected on Ethernet networks.

Ethernet CFM OAM is an E2E fault detection technology, which can be used to monitor,
diagnose, and troubleshoot the Ethernet.

Networking

shows the example network of the Ethernet CFM OAM function.

Figure 4-1

Example network of the Ethernet CFM OAM function

MA5616_A

MA5616_B

0/0/0

0/0/0

Router

SmartAX MA5616 Multi-service Access Module
Configuration Guide

4 Configuring the Ethernet CFM OAM

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

153

«
...
162
163
164
165
166
...
»

Summary of Contents for SmartAX MA5616










































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SmartAX MA5616

Brand: 3Com Pages: 8

8 Port 10/100Mbit/s Ethernet Smart Switch with Fibre Uplink

Brand: Tyco Electronics Pages: 18

Brand: M2M Pages: 9

Brand: FabiaTech Pages: 4

Compact Emulator M30620T-CPE

Brand: Renesas Pages: 52

ER3-100 (5K02-55)

Brand: 8e6 Technologies Pages: 74

Brand: Abocom Pages: 1

Brand: APARIAN Pages: 2

Brand: Telex Communications Pages: 28

Brand: Lanner electronics Pages: 59

IPAM-1600s Series

Brand: C-Com Pages: 148

PCIe/PXIe-6301 Series

Brand: JYTEK Pages: 46

Brand: Caton Pages: 18

Brand: Airlink101 Pages: 46

Brand: VideoWave Pages: 12

Brand: Raven Pages: 33

Brand: ADS Technologies Pages: 1

Brand: CSL Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands