manualshive.com logo in svg

Huawei SmartAX MA5616, Configuration Manual

The Huawei SmartAX MA5616 Configuration Manual is a detailed and comprehensive guide that enables users to efficiently set up and optimize their Huawei SmartAX MA5616. Easily downloadable for free from manualshive.com, this manual provides step-by-step instructions and essential information to maximize your product experience.

Share
Download
background image

5

 Configuring the xDSL Internet Access

Service

About This Chapter

xDSL broadband Internet access is applicable in the scenario where the Internet service is
provided through the ordinary twisted pairs. In this scenario, a user can access Internet in IPoE,
PPPoE, IPoA, PPPoA, or 802.1X mode. This topic describes how to configure an xDSL Internet
access service on the MA5616.

Prerequisite

PPPoE or PPPoA Internet access mode:

l

Configure the AAA function.

–

To enable the AAA function on the device, see 

3.12 Configuring AAA

.

–

If the AAA function is implemented by the BRAS, a connection to the BRAS must be
established. The BRAS should be capable of identifying the VLAN tag of the
MA5616 in the upstream direction. For the identification purpose, the user name and
password for dial-up Internet access must be configured on the BRAS.

l

The xDSL profile for the Internet access service must be created.

–

3.7.1 Configuring the ADSL2+ Profile

–

3.7.2 Configuring the SHDSL Profile

–

3.7.3.1 Configuring the VDSL2 Profile (Normal Mode)

–

3.7.3.2 Configuring the VDSL2 Profile (TI Mode)

IPoE or IPoA Internet access mode:

l

3.7.1 Configuring the ADSL2+ Profile

l

3.7.2 Configuring the SHDSL Profile

l

3.7.3.1 Configuring the VDSL2 Profile (Normal Mode)

l

3.7.3.2 Configuring the VDSL2 Profile (TI Mode)

SmartAX MA5616 Multi-service Access Module
Configuration Guide

5 Configuring the xDSL Internet Access Service

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

157

Summary of Contents for SmartAX MA5616










































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SmartAX MA5616

Samsung AllShare Cast Dongle Quick Start Manual preview
AllShare Cast Dongle
Brand: Samsung Pages: 2
D-Link DSL-2750U Setup preview
DSL-2750U
Brand: D-Link Pages: 14
D-Link DVG-7022S Quick Installation Manual preview
DVG-7022S
Brand: D-Link Pages: 7
D-Link DIR-878 Quick Installation Manual preview
DIR-878
Brand: D-Link Pages: 41
Magnat Audio MC 200 Faq preview
MC 200
Brand: Magnat Audio Pages: 2
3Com OfficeConnect 1600 Datasheet preview
OfficeConnect 1600
Brand: 3Com Pages: 8
3Com 3CRWEASY96A Quick Start Manual preview
3CRWEASY96A
Brand: 3Com Pages: 8
Aastra CNX Product Brief preview
CNX
Brand: Aastra Pages: 2
Idis DR-6100 Series Operation Manual preview
DR-6100 Series
Brand: Idis Pages: 86
Paradyne Hotwire 6301 Installation Instructions Manual preview
Hotwire 6301
Brand: Paradyne Pages: 20
Paradyne COMSPHERE 3610 Installation Instructions preview
COMSPHERE 3610
Brand: Paradyne Pages: 2
hawa HAWA-Frontside 60/B Planning And Installation Instructions preview
HAWA-Frontside 60/B
Brand: hawa Pages: 28
Opengear IMG4216-25 Quick Start Manual preview
IMG4216-25
Brand: Opengear Pages: 2
process-informatik CONNECT Series Operation Quick Start Manual preview
CONNECT Series
Brand: process-informatik Pages: 8
C-Com IPAM-1600s Series User Manual preview
IPAM-1600s Series
Brand: C-Com Pages: 148
Kontron 50099 067 User Manual preview
50099 067
Brand: Kontron Pages: 42
impinj Speedway Revolution Installation And Operation Manual preview
Speedway Revolution
Brand: impinj Pages: 60
ZyXEL Communications VMG5313-BXB SERIES Quick Start Manual preview
VMG5313-BXB SERIES
Brand: ZyXEL Communications Pages: 2

Brands by name

Popular brands

Load more brands