manualshive.com logo in svg

Huawei SmartAX MA5616, Configuration Manual

The Huawei SmartAX MA5616 Configuration Manual is a detailed and comprehensive guide that enables users to efficiently set up and optimize their Huawei SmartAX MA5616. Easily downloadable for free from manualshive.com, this manual provides step-by-step instructions and essential information to maximize your product experience.

Share
Download
background image

the maximum interleave delay is 10 ms, and the SNR margin is 6 dB. To configure such an
ADSL2+ line template, do as follows:

huawei(config)#

adsl line-profile quickadd 3 snr 60 30 120 60 30 120

huawei(config)#

adsl channel-profile quickadd 3 interleaved-delay 10 10 rate 1024

 2048 3096 1024 2048 3096  

                                                     

huawei(config)#

adsl line-template quickadd 3 line 3 channel1 3 60 70 channel2 3

3.7.2 Configuring the SHDSL Profile

This topic describes how to configure the SHDSL line profile and alarm profile.

Context

The SHDSL line profile and alarm profile can be directly bound to an SHDSL port.

Table 3-11

 lists the default SHDSL profiles.

Table 3-11

 Default SHDSL profiles

Parameter

Default Setting

SHDSL line profile

Profile IDs: 1, 100, 101, 102, and 103
Profile 1 is used to activate the 2-wire ATM SHDSL
port. Profile 100 is used to activate the 4-wire ATM
SHDSL port. Profile 101 is used to activate the 6-
wire ATM SHDSL port. Profile 102 is used to
activate the 8-wire ATM SHDSL port. Profile 103
is used to activate the EFM-bonding SHDSL port.

SHDSL alarm profile

Profile ID: 1

 

Procedure

l

Configure an SHDSL line profile.

Run the 

shdsl line-profile quickadd

 command to quickly add an SHDSL line profile, or

run the 

shdsl line-profile add

 command to interactively add an SHDSL line profile.

Main parameters:

–

ptm

: If the SHDSL channel mode is the ATM mode, do not select 

ptm

. If the SHDSL

channel mode is the PTM mode, select 

ptm

.

–

rate

: Indicates the line rate. During line activation, a proper rate between the preset

maximum rate and minimum rate is determined through automatic negotiation
according to the line condition and the profile configuration. The user rate can be
restricted by this rate or the rate set in the traffic profile that is bound to the user. When
both rates function, the lower rate is selected as the user rate.

–

transmission

: Indicates the transmission mode. Set the transmission mode according

to line conditions and actual planning. Three transmission modes are supported: annex
A, annex L, and annex A&B.

–

snr-margin

: The larger the SNR margin, the better the line stability, and meanwhile

the lower the physical connection rate of the line after activation. For common Internet

SmartAX MA5616 Multi-service Access Module
Configuration Guide

3 Basic Configuration

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

60

Summary of Contents for SmartAX MA5616










































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SmartAX MA5616

Raritan DOMINION SX - Quick Setup Manual preview
DOMINION SX -
Brand: Raritan Pages: 4
Rane CP 31 Datasheet preview
CP 31
Brand: Rane Pages: 4
Quantum LightSpeed Appliance QLS250 Owner'S Manual preview
LightSpeed Appliance QLS250
Brand: Quantum Pages: 12
DAQ system PCIe-FRM13 User Manual preview
PCIe-FRM13
Brand: DAQ system Pages: 41
DAQ system PCIe-SER01 User Manual preview
PCIe-SER01
Brand: DAQ system Pages: 19
ekwb EK-Vector Radeon RX5700 + XT Backplate Installation Manual preview
EK-Vector Radeon RX5700 + XT Backplate
Brand: ekwb Pages: 7
Tandberg Data Storagelibrary T24 Manual preview
Storagelibrary T24
Brand: Tandberg Data Pages: 28
Idis DR-8400 Installation Manual preview
DR-8400
Brand: Idis Pages: 31
Paxton Net2Air Ins-40085-US Quick Start Manual preview
Net2Air Ins-40085-US
Brand: Paxton Pages: 4
ZyXEL Communications GS3700 Series Handbook preview
GS3700 Series
Brand: ZyXEL Communications Pages: 215
Hama 00039747 Operating Instruction preview
00039747
Brand: Hama Pages: 6
ADS Technologies PTV-352-EFG Hardware Quickmanual preview
PTV-352-EFG
Brand: ADS Technologies Pages: 1
Advantech ARK-1380 User Manual preview
ARK-1380
Brand: Advantech Pages: 50
Xantech CC12 Installation Instructions preview
CC12
Brand: Xantech Pages: 4
Juniper E SERIES BROADBAND SERVICES ROUTERS 11.3.X - ERX MODULE GUIDE REV 27-9-2010 Manual preview
E SERIES BROADBAND SERVICES ROUTERS 11.3.X - ERX MODULE GUIDE REV 27-9-2010
Brand: Juniper Pages: 122
ACTi GNR-310 Quick Installation Manual preview
GNR-310
Brand: ACTi Pages: 12
NBase NH 210 Installation And User Manual preview
NH 210
Brand: NBase Pages: 18
Gearlinx NR4400 Series User'S Quick Start Manual preview
NR4400 Series
Brand: Gearlinx Pages: 23

Brands by name

Popular brands

Load more brands