Huawei SmartAX MA5616 Configuration Manual Download | Manualshive

Page: 68 / 553

background image

NOTE

l

To configure attributes for the VLANs with consecutive IDs in batches, run the

vlan attrib vlanid to end-

vlanid

command.

l

To configure attributes for the VLANs with inconsecutive IDs in batches, run the

vlan attrib vlan-list

command.

Step 3

(Optional) Configure VLAN description.

To configure VLAN description, run the

vlan desc

command. You can configure VLAN

description to facilitate maintenance. The general VLAN description includes the usage and
service information of the VLAN.

Step 4

(Optional) Configure the VLAN forwarding policy.

vlan-connect

corresponds to the S+C forwarding policy, which ensures higher security by

solving the problems of insufficiency in the MAC address space, MAC address aging, and MAC
address spoofing and attacks.

To configure the VLAN forwarding policy in the VLAN service profile, do as follows:

1.

Run the

vlan service-profile

command to create a VLAN service profile and enter the

VLAN service profile mode.

2.

Run the

forwarding

command to configure the VLAN forwarding policy. The default

VLAN forwarding policy is VLAN+MAC in the system.

3.

Run the

commit

command to validate the profile configuration. The configuration of the

VLAN service profile takes effect only after execution of this command.

4.

Run the

quit

command to quit the VLAN service profile mode.

5.

Run the

vlan bind service-profile

command to bind the VLAN to the VLAN service profile

----End

Example

Assume that a QinQ VLAN with ID of 100 is to be configured for an enterprise user to ensure
higher security and the VLAN forwarding policy is S+C. For the VLAN, description needs to
be configured for easy maintenance. To configure such a VLAN, do as follows:

huawei(config)#

vlan 100 smart

huawei(config)#

vlan attrib 100 q-in-q

huawei(config)#

vlan desc 100 description qinqvlan/forhuawei

huawei(config)#

vlan service-profile profile-id 1

huawei(config-vlan-srvprof-1)#

forwarding vlan-connec

Info: Please use the commit command to make modifications take effect
huawei(config-vlan-srvprof-1)#

commit

huawei(config-vlan-srvprof-1)#

quit

huawei(config)#

vlan bind service-profile 100 profile-id 1

3.7 Configuring the xDSL Profile

Configuring the xDSL profile is a prerequisite for configuring an xDSL access service. This
topic describes how to configure an ADSL2+ profile, an SHDSL profile, and a VDSL2 profile.

3.7.1 Configuring the ADSL2+ Profile

This topic describes how to configure an ADSL2+ line profile and an ADSL2+ line alarm profile.

SmartAX MA5616 Multi-service Access Module
Configuration Guide

3 Basic Configuration

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

57

«
...
66
67
68
69
70
...
»

Summary of Contents for SmartAX MA5616










































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SmartAX MA5616

Brand: M2M Pages: 9

SR8800 IM-FW-II

Brand: H3C Pages: 107

Brand: 3Com Pages: 12

Brand: H3C Pages: 16

H3C S3600 Series

Brand: H3C Pages: 10

Brand: H3C Pages: 42

Brand: H3C Pages: 2

H3C S7500E Series

Brand: H3C Pages: 34

Brand: H3C Pages: 33

Brand: H3C Pages: 14

Brand: H3C Pages: 56

H3C S7500E Series

Brand: H3C Pages: 112

Brand: H3C Pages: 15

SR8800 IM-FW-II

Brand: H3C Pages: 5

H3C S7500E Series

Brand: H3C Pages: 50

Brand: H3C Pages: 37

Brand: H3C Pages: 4

Brand: H3C Pages: 5

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands