Huawei SmartAX MA5616 Configuration Manual Download

Page: 483 / 553

huawei(config)#

service-port 10 vlan 105 vdsl mode atm 0/1/0 vpi 0 vci 35

multi-serv
ice user-8021p 4 rx-cttr 9 tx-cttr 9

huawei(config)#

service-port 11 vlan 105 vdsl mode atm 0/1/1 vpi 0 vci 35

multi-serv
ice user-8021p 4 rx-cttr 9 tx-cttr 9

CAUTION

On the MA5616, if the PVC is configured with a priority, the priority of the multicast
packets carried by the PVC does not take effect.

Configure the multicast data.

To provision the multicast video service, you also need to configure IGMP proxy and
programs.

Add a multicast VLAN and configure the multicast mode.

huawei(config)#

multicast-vlan 104

huawei(config-mvlan104)#

igmp mode

proxy

Are you sure to change IGMP mode?(y/n)[n]:

NOTE

Select a multicast mode according to the actual requirements. In this example, the IGMP
proxy mode is considered.

Configure the multicast uplink port.

huawei(config-mvlan104)#

igmp uplink-port 0/0/1

huawei(config-mvlan104)#

btv

huawei(config-btv)#

igmp uplink-port-mode

default

Are you sure to change the uplink port mode?(y/n)[n]:

Configure the program library.

huawei(config-btv)#

multicast-vlan 104

huawei(config-mvlan104)#

igmp program add name program1 ip 224.1.1.1

sourceip 10.
10.10.10

huawei(config-mvlan104)#

igmp program add name program2 ip 224.1.1.2

sourceip 10.
10.10.11

huawei(config-mvlan104)#

quit

Configure the right profile.

huawei(config)#

btv

huawei(config-btv)#

igmp profile add profile-name profile0

huawei(config-btv)#

igmp profile profile-name profile0 program-name

program1 watc
h

Configure multicast users.

huawei(config-btv)#

igmp user add service-port 10

huawei(config-btv)#

igmp user add service-port 11 auth

huawei(config-btv)#

igmp user bind-profile service-port 11 profile-

name profile0

huawei(config-btv)#

quit

huawei(config)#

multicast-vlan 104

huawei(config-mvlan104)#

igmp multicast-vlan member service-port 10

huawei(config-mvlan104)#

igmp multicast-vlan member service-port 11

huawei(config-mvlan104)#

quit

Save the data.

huawei(config)#

save

----End

SmartAX MA5616 Multi-service Access Module
Configuration Guide

9 Configuration Example of Services on the MA5616

Through GE Upstream Transmission

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

472

Summary of Contents for SmartAX MA5616










































































































































































































































































































































































































































































































































































Search results

Summary of Contents for SmartAX MA5616

Reviews:

Related manuals for SmartAX MA5616

Brands by name

Popular brands

Huawei SmartAX MA5616, Configuration Manual

Search results

Summary of Contents for SmartAX MA5616

Reviews:

Related manuals for SmartAX MA5616

Brands by name

Popular brands