Huawei SmartAX MA5616 Configuration Manual Download | Manualshive

Page: 223 / 553

background image

Item

Remarks

Overseas Parameters

The attributes such as the upper and
lower thresholds of the flash-hooking
duration need to be configured
according to the local standards to
ensure that the response of the user
terminal complies with the local
standards.

Local Digitmap

Configure a proper local digitmap
according to the local standards. If the
MGC does not send the detailed
digitmap to the MA5616, the MA5616
uses the local digitmap to match the
phone number.

CAUTION

If the H.248 protocol is used, the local
digitmap need not be configured by default.
You can configure the local digitmap
according to the requirements.

Attributes of a PSTN Port

If the PSTN port needs to support the
polarity reversal charging, the PSTN
port needs to be configured to support
the polarity reversal pulse. Other
attributes need not be modified if there
is no special requirement.

Attributes of the Ringing
Current

You can adjust the ringing tone volume
by modifying the attributes of the
ringing current. Generally, the
attributes of the ringing current need not
be modified. You need to modify the
parameters of the ringing current
attributes according to the local
standards only when the default ringing
current attributes do not meet the local
standards.

7.1.1 Configuring an MG Interface

This topic describes how to configure an MG interface for implementing the communication
between the MA5616 (AG) and the MGC.

Context

l

The MA5616 communicates with the MGC through the MG control protocol, that is, the
H.248 protocol.

l

One MA5616 supports up to one MG interface. The MG interface can be configured with
the attributes such as authentication and ringing mapping.

SmartAX MA5616 Multi-service Access Module
Configuration Guide

7 Configuring the Voice Service

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

212

«
...
221
222
223
224
225
...
»

Summary of Contents for SmartAX MA5616










































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SmartAX MA5616

Brand: Abus Pages: 60

Brand: Zonet Pages: 10

Brand: Samsung Pages: 65

Brand: D-Link Pages: 176

Brand: Alcad Pages: 6

PowerBeam AC Gen2

Brand: Ubiquiti Pages: 22

Brand: Roland Pages: 2

Brand: Realtek Pages: 30

Brand: Garderos Pages: 23

Brand: A2B Electronics Pages: 24

Brand: ZALMAN Pages: 6

TD-3316B4-16P-A1

Brand: TVT Digital Pages: 2

Brand: LevelOne Pages: 26

Brand: ZyXEL Communications Pages: 3

Brand: ZiLOG Pages: 317

Brand: Wave Wireless Networking Pages: 167

Brand: Edimax Pages: 15

Brand: Neousys Technology Pages: 39

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands