manualshive.com logo in svg

Huawei SmartAX MA5616, Configuration Manual

The Huawei SmartAX MA5616 Configuration Manual is a detailed and comprehensive guide that enables users to efficiently set up and optimize their Huawei SmartAX MA5616. Easily downloadable for free from manualshive.com, this manual provides step-by-step instructions and essential information to maximize your product experience.

Share
Download
background image

l

The MA5616 supports a maximum of eight local digitmaps.

l

For the meaning of each character in the digitmap body, see the Context in 

7.1.1.4

(Optional) Configuring the Digitmap of an MG Interface

.

Precaution

l

When the H.248 protocol is used, the type of the local digitmap can only be normal.

l

When the SIP protocol is used, the type of the local digitmap can be normal, emergency,
scc, direct-centrex, or second-centrex. For the meaning of the digitmap type, see the
Parameter Description in the 

local-digitmap add

 command.

Procedure

Step 1

In privilege mode, run the 

display protocol support

 command to query the current protocol

type used on the MA5616.

l

When the H.248 protocol is used, go to 

Step 5

.

l

When the SIP protocol is used, go to 

Step 2

.

Step 2

In privilege mode, run the 

display local-digitmap

 command to query the default local digitmap.

l

If the default local digitmap can meet the requirements, the configuration is complete.

l

If the default local digitmap cannot meet the requirements, perform one or more operations
in 

Step 3

, 

Step 4

, and 

Step 5

 to configure a proper local digitmap.

Step 3

Run the 

local-digitmap modify

 command to change the name, type, or body of the local

digitmap.

Step 4

Run the 

local-digitmap append

 command to add a digitmap body in the local digitmap.

Step 5

According to the data plan, run the 

local-digitmap add

 command to add a local digitmap.

Step 6

Run the 

display local-digitmap

 command to check whether the local digitmap is the same as

the planned local digitmap.

----End

Example

Assume that the H.248 protocol is used on the MA5616. To add a local digitmap with the data
listed in 

Table 7-9

, do as follows:

Table 7-9

 Local digitmap existing in the system

Digitmap Name

Digitmap Type

Digitmap Body

huawei

normal

([2-8]xxxxxxx|[2-8]
xxSxxxxxxx|13xxxxxxxxx|
0xxxxxxxxx|9xxxx|1
[0124-9]x|F|x.F|[0-9].S)

 

huawei(config)#

local-digitmap add huawei normal ([2-8]xxxxxxx|[2-8]xxSxxxxxxx|13

xxxxxxxxx|0xxxxxxxxx|9xxxx|1[0124-9]x|F|x.F|[0-9].S)

huawei(config)#

display local-digitmap all

  ------------------------------------------

SmartAX MA5616 Multi-service Access Module
Configuration Guide

7 Configuring the Voice Service

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

238

Summary of Contents for SmartAX MA5616










































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SmartAX MA5616

GE Mini Field Agent User Manual preview
Mini Field Agent
Brand: GE Pages: 87
Linksys WRT54G3G-AT Product Data preview
WRT54G3G-AT
Brand: Linksys Pages: 2
Q-See QC814 Specifications preview
QC814
Brand: Q-See Pages: 2
NXP Semiconductors MIMXRT1160 Hardware Development Manual preview
MIMXRT1160
Brand: NXP Semiconductors Pages: 24
Aztech DSL5068EN(1T1R) User Manual preview
DSL5068EN(1T1R)
Brand: Aztech Pages: 40
Rabbit RabbitCore RCM4400W Product Manual preview
RabbitCore RCM4400W
Brand: Rabbit Pages: 126
4Home ControlPoint 2000 User Manual preview
ControlPoint 2000
Brand: 4Home Pages: 20
C&T Solution RCO-3000 Series User Manual preview
RCO-3000 Series
Brand: C&T Solution Pages: 96
TRENDnet TEW-733GR User Manual preview
TEW-733GR
Brand: TRENDnet Pages: 62
Ravpower RD-WD009 User Manual preview
RD-WD009
Brand: Ravpower Pages: 27
IEI Technology HPE-6S2 Quick Installation Manual preview
HPE-6S2
Brand: IEI Technology Pages: 3
Eneo PNR-5304 Quick Installation Manual preview
PNR-5304
Brand: Eneo Pages: 68
IBASE Technology FWA8207 Series User Manual preview
FWA8207 Series
Brand: IBASE Technology Pages: 39
ZALMAN CNPS5700D-Cu User Manual preview
CNPS5700D-Cu
Brand: ZALMAN Pages: 7
Altera Stratix II User Manual preview
Stratix II
Brand: Altera Pages: 33
Radica Games DAVID-II 716 Operating And Maintenance Instruction Manual preview
DAVID-II 716
Brand: Radica Games Pages: 40
Airvana ipBTS C30 Installation And Commissioning Manual preview
ipBTS C30
Brand: Airvana Pages: 90
Renesas HD74HCT1G04 Datasheet preview
HD74HCT1G04
Brand: Renesas Pages: 8

Brands by name

Popular brands

Load more brands