Huawei SmartAX MA5616 Configuration Manual Download | Manualshive

Page: 145 / 553

background image

3.15.1.2 Configuring the Monitoring Through the ESCM

The ESCM is an EMU that integrates the environment monitoring board, terminal blocks, and
DIP switches. The ESCM monitors the environment parameters such as smoke, water, door
status, wiring, temperature, and humidity of the device, and also provides extended monitoring
ports. This topic provides the basic information about the ESCM and describes how to configure
analog and digital parameters of the ESCM.

Prerequisites

l

The ESCM must be connected to the ESC port of the control board on the MA5616 through
a straight-through cable.

l

The setting of the hardware DIP switch on the ESCM must be the same as the configured
EMU subnode ID.

NOTE

For details about the settings of DIP switches, see ESCM EMU.

l

The sixth DIP switch on the ESCM must be set to on, which indicates that the baud rate is
19200 bit/s.

Context

l

The differences between an analog parameter and a digital parameter are as follows:

–

An analog parameter is a consecutive parameter, such as the temperature, voltage, and
current.

–

A digital parameter is a discrete value that indicates a state.

l

The ESCM requires an RS-485 serial port for data communication.

l

In the case of the ESCM, the system supports the following analog and digital parameters:

–

Analog parameters 0-1: invariably allocated by the system. You cannot modify any
parameter in these two analog parameters, except the upper and lower alarm thresholds.

–

Analog parameters 2-3: user-defined.

–

Digital parameters 0, 1, 8, and 9: invariably allocated by the system. You cannot modify
any parameter in these digital parameters, except the valid level.

NOTE

Digital parameter 9

Water_Alarm

: unavailable.

–

Digital parameters 2-7: user-defined.

Mapping Between Monitoring Parameters and Device Ports

describes the mapping between the monitoring parameters displayed on the host and

the ports on the ESCM.

Table 3-24

Mapping between the monitoring parameters displayed on the host and the ports on

the ESCM

Monitoring Parameter on Host

Device Port

Temperature

Temperature

Input_-48V_0

Voltage

SmartAX MA5616 Multi-service Access Module
Configuration Guide

3 Basic Configuration

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

134

«
...
143
144
145
146
147
...
»

Summary of Contents for SmartAX MA5616










































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SmartAX MA5616

Brand: Watchguard Pages: 40

Brand: D-Link Pages: 11

Brand: D-Link Pages: 8

AirPlus DWL-810

Brand: D-Link Pages: 8

Brand: D-Link Pages: 12

Brand: D-Link Pages: 84

Brand: Xantrex Pages: 8

Brand: N-Tron Pages: 138

Brand: BSS Audio Pages: 20

Brand: Reeven Pages: 2

Brand: Orban Pages: 255

Brand: Stephen Pages: 102

Brand: AirTies Pages: 28

SW-UNM-24FE2GC-24POE

Brand: Morrell Pages: 8

Total Access 1500 Dual FXS/DPO

Brand: ADTRAN Pages: 2

Brand: FDI Pages: 15

Internet Security Appliances

Brand: SonicWALL Pages: 293

Brand: Panduit Pages: 5

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands